ADG904BRU-R-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG904 |
| Pin Count | 20 |
| JESD-30 Code | R-PDSO-G20 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 2.75V |
| Number of Channels | 4 |
| Number of Circuits | 1 |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Bandwidth | 2.5 GHz |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 37 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 2pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 10ns, 16ns |
| Crosstalk | -58dB @ 100MHz |
| Voltage - Supply, Single (V+) | 1.65V~2.75V |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
ADG904BRU-R-REEL Overview
Shipping overseas is convenient due to the electrical component's packing in 20-TSSOP (0.173, 4.40mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Mounted in Surface Mount is this multiplexer. 4:1 is the ratio between multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 20. A high-quality output is provided by the electrical component's 4 channels. In the case of a voltage supply of 2.5V volts, the electrical part can be powered up and run. It is part of the design of the 20 series that this electronic component is included. Circuits based on SP4T switching are used to construct these analog switch ics. A total of 1 circuits make up this switch device. Try searching with ADG904 if you're looking for variants. A voltage of 1.65V~2.75V is required to drain this analog switch from a single voltage supply. There is an integrated analog IC SINGLE-ENDED MULTIPLEXER in the module. 2.75V operating voltages are supported by the electronic component. A 2.5 GHz-bandwidth can be used for data transfer. A analog switch ics with 4 outputs is included.
ADG904BRU-R-REEL Features
4 Channels
Switch Circuit: SP4T
Bandwidth: 2.5 GHz
ADG904BRU-R-REEL Applications
There are a lot of Analog Devices Inc. ADG904BRU-R-REEL Analog Switches & Multiplexers ICs applications.
- Medical
- HDTV
- SDH/SONET multiplexers
- Battery Powered Systems
- RGB switches
- SONET/SDH ADM
- Communications systems
- SONET
- E1 Network Equipment
- Data Acquisition Systems
