ADM690SQ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-CDIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Tin/Lead (Sn63Pb37) |
| Additional Feature | RESET CONTROL |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | ADM690 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.75V |
| Operating Supply Current | 1.95mA |
| Nominal Supply Current | 1.95mA |
| Power Dissipation | 500mW |
| Max Supply Current | 1.95mA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.65V |
| Reset Timeout | 35ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.73V |
| Undervoltage Threshold | 1.3V |
| Overvoltage Threshold | 5V |
| Number of Monitored Inputs | 1 |
| Reset Delay Time | 70 ms |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADM690SQ Overview
There are 8 terminals connected to this power management, which makes it easy to mount. A Tube package is used to package the power management. As a reference, this IC management includes 1 functions for your convenience. There are 1 channels available on this supervisor, and each channel has a different function. There are 8-CDIP (0.300, 7.62mm) functions included in this PMIC so that you can refer to them. There are a lot of similarities between this IC management and other Battery Backup Circuit products. The supervisor is always powered by a 5V volt supply. The mount is attached to Through Hole. A IC power such as this can be classified as a Power Management Circuits power management system. In total, the power management has 8 pins in it. The pins of the power management system count 8. I should note that the minimum supply voltage (Vsup) for this IC management should be at least 4.75V, which is the minimum supply voltage that should be applied. There should be no more than 5.5V volts of supply voltage (Vsup) in this power management. Power management recommends the Through Hole mounting type. This range of temperature should be set for the supervisors: -55°C~125°C TA. As a result of this supervisor's operation, the output voltage is Push-Pull, Totem Pole. There is a 1.95mA supply current present in the power management. There are also other features in the software such as [0], just to mention a few. You can always use ADM690, the base supervisor number, to search for similar PMICs of the manufacturer. The voltage supervisor requires a power source of 5V volts in order to work correctly. The maximum supply temperature is 1.95mA. On the power management, 1 inputs are monitored.
ADM690SQ Features
Battery Backup Circuit type
Minimum supply voltage of 4.75V
1.95mA operating supply current
ADM690SQ Applications
There are a lot of Analog Devices Inc. ADM690SQ Voltage Supervisors applications.
- Detection of phase loss
- Battery-powered equipment
- Dash board
- Leakage protection
- Embedded computing
- DC stabilized power supply module
- Network equipment
- Urban rail transit weak current power monitoring
- Microcontroller system
- Functional modules
