Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 3 weeks ago) |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Type |
Battery Backup Circuit |
Terminal Finish |
Matte Tin (Sn) |
Additional Feature |
RESET CONTROL |
Subcategory |
Power Management Circuits |
Max Power Dissipation |
600mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
2.54mm |
Base Part Number |
ADM695 |
Output |
Open Drain, Push-Pull |
Pin Count |
16 |
Power Supplies |
5V |
Number of Channels |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
4.75V |
Operating Supply Current |
1.95mA |
Nominal Supply Current |
1.95mA |
Power Dissipation |
600mW |
Max Supply Current |
1.95mA |
Adjustable Threshold |
NO |
Watchdog Timer |
Yes |
Reset |
Active High/Active Low |
Voltage - Threshold |
4.65V |
Reset Timeout |
140ms Minimum |
Min Reset Threshold Voltage |
4.5V |
Max Reset Threshold Voltage |
4.73V |
Undervoltage Threshold |
4.5V |
Overvoltage Threshold |
4.73V |
Number of Monitored Inputs |
1 |
Reset Delay Time |
280 ms |
Height |
4.95mm |
Length |
21.33mm |
Width |
7.11mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADM695ANZ Overview
There are 16 terminals connected to this power management, which makes it easy to mount. A Tube package is used to package the power management. Please find attached 1 functions for your reference in this IC power. A series of 1 channels can be found on this supervisor. In this IC management you will find 16-DIP (0.300, 7.62mm) functions for you to refer to. This IC power shares lots of benefits with other Battery Backup Circuit products. Manage ics operate at 5V supply voltages. Using Through Hole, IC management is mounted. As a subcategory, this PMIC chip can be categorized as Power Management Circuits. In total, IC powers are 16 pins on the board. This power management system has 16 pins. I should note that the minimum supply voltage (Vsup) for this IC management should be at least 4.75V, which is the minimum supply voltage that should be applied. In this PMIC, the maximum supply voltage (Vsup) should not exceed 5.5V volts. Through Hole mounting is recommended. We recommend setting the supervisors to -40°C~85°C TA degrees. There is an output voltage of Open Drain, Push-Pull from this supervisor when it is operating. As far as the supply current of the power management is concerned, it is 1.95mA. In addition, IC management are other features such as [0], to mention only a few. A similar IC managements number of the manufacturer can always be found by using ADM695, the base power ics number. It requires 5V watts of power to operate this voltage supervisor. If you want to work with PMIC chip, you will need to supply PMIC chip with a temperature at least of 1.95mA. In total, the voltage supervisor has 1 inputs which are monitored at the same time.
ADM695ANZ Features
Battery Backup Circuit type
Minimum supply voltage of 4.75V
1.95mA operating supply current
ADM695ANZ Applications
There are a lot of Analog Devices Inc. ADM695ANZ Voltage Supervisors applications.
- Battery cars
- Radio
- Automotive permanent magnet synchronous motors
- Digitally controlled LDO regulators circuit
- Functional modules
- Fire equipment power monitoring system
- Medical-specific isolation transformer
- Detection of phase loss
- Transformer load monitoring equipment
- Battery cars