ADM706ANZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | ADM706 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 250μA |
| Nominal Supply Current | 250μA |
| Power Dissipation | 727mW |
| Max Supply Current | 250μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.4V |
| Reset Timeout | 160ms Minimum |
| Min Reset Threshold Voltage | 4.25V |
| Max Reset Threshold Voltage | 4.5V |
| Undervoltage Threshold | 4.25V |
| Overvoltage Threshold | 4.5V |
| Number of Monitored Inputs | 1 |
| Reset Delay Time | 280 ms |
| Height | 3.43mm |
| Length | 9.27mm |
| Width | 7.24mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADM706ANZ Overview
Power management is mounted through 8 terminals. A Tube package is used to package the power management. Power management is possible to find a series of 1 functions. Depending on the power managment ic you are looking at, you can find a total of 2 channels. Please find attached 8-DIP (0.300, 7.62mm) functions for your reference in this IC power. Several of the benefits of this PMIC are also shared by other Simple Reset/Power-On Reset products. The supervisor is always powered by a 5V volt supply. Through Hole mounts power management on the wall. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. In total, the power management has 8 pins in it. This power management has 8 pins. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1V. There should be no more than 5.5V volts of maximum supply voltage (Vsup) in this power management. Power management recommends the Through Hole mounting type. It is recommended that the supervisor be set to this temperature: -40°C~85°C TA. While this power management is operating, it will output Push-Pull, Totem Pole as the output voltage. There is a supply current of 250μA for the power management. To find similar IC managements from the manufacturer, you can always search by ADM706. To be able to work, this power management requires 5V volts of power. The maximum supply temperature that PMIC chip can work with is 250μA. On the supervisor, a total of 1 inputs are monitored as IC management of its monitoring system.
ADM706ANZ Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1V
250μA operating supply current
ADM706ANZ Applications
There are a lot of Analog Devices Inc. ADM706ANZ Voltage Supervisors applications.
- Military electronics
- Satellite navigation
- Digitally controlled LDO regulators circuit
- Smartphones
- Linux and server computing
- Efficient information transmission
- FPGA design
- Battery cars
- Dash board
- DVR
