ADM805LANZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 weeks ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| Base Part Number | ADM805 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 3 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1V |
| Operating Supply Current | 100μA |
| Nominal Supply Current | 100μA |
| Power Dissipation | 400mW |
| Max Supply Current | 100μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High |
| Voltage - Threshold | 4.65V |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Number of Monitored Inputs | 1 |
| Reset Delay Time | 280 ms |
| Height | 3.43mm |
| Length | 9.27mm |
| Width | 7.24mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADM805LANZ Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 8 in total. Power management is packaged in a Tube way. Power management is possible to find a series of 1 functions. Power management consists of 3 channels, each of which can be used independently. IC management is packaged as a 8-DIP (0.300, 7.62mm) package. This IC power shares lots of benefits with other Battery Backup Circuit products. As specified in the package specification, the peak reflow temperature of the package is set at NOT APPLICABLE. When 5V is applied to the power ic, it conducts. The mount is provided by Through Hole. 8 pins are present in total in this power management. There are 8 pins on the supervisor. It is recommended that Vsup should not be less than 1V for this IC power. The supply voltage (Vsup) should not exceed 5.5V volts in this IC power. The recommended mounting type for IC management is Through Hole. It is recommended to set the supervisor's temperature to this range: -40°C~85°C TA. During operation, this power management system outputs Push-Pull, Totem Pole. For this power management, there is an 100μA volt supply current. For similar manage ics search of the manufacturer, you can always refer to ADM805, the base PMIC number. The maximum supply temperature that PMIC chip can work with is 100μA. The power management has 1 monitored inputs.
ADM805LANZ Features
Battery Backup Circuit type
Minimum supply voltage of 1V
100μA operating supply current
ADM805LANZ Applications
There are a lot of Analog Devices Inc. ADM805LANZ Voltage Supervisors applications.
- Solar power charger
- Microprocessor system
- Network equipment
- Smartphones
- Leakage current detection
- Battery cars
- Medical-specific insulation monitor
- Radio
- emergency room
- Electrical fire monitoring system
