ADP198ACBZ-R7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 4-UFBGA, WLCSP |
| Number of Pins | 4 |
| Weight | 68.407399mg |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Cut Tape (CT) |
| Feature | Slew Rate Controlled |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 4 |
| ECCN Code | EAR99 |
| Resistance | 50mOhm |
| Subcategory | Peripheral Drivers |
| Technology | DMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Number of Functions | 1 |
| Supply Voltage | 2.8V |
| Terminal Pitch | 0.5mm |
| Base Part Number | ADP198 |
| Pin Count | 4 |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Max Output Current | 1A |
| Operating Supply Voltage | 6.5V |
| Power Supplies | 2.8V |
| Interface | On/Off |
| Operating Supply Current | 1.1μA |
| Output Configuration | High Side |
| Output Current | 1A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Turn On Delay Time | 450 μs |
| Switch Type | General Purpose |
| Min Input Voltage | 1.65V |
| Max Input Voltage | 6.5V |
| Nominal Input Voltage | 6.5V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 1.65V~6.5V |
| Driver Number of Bits | 1 |
| Fault Protection | Reverse Current |
| Rds On (Typ) | 40m Ω |
| Height | 370μm |
| Length | 990μm |
| Width | 1.065mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADP198ACBZ-R7 Overview
Cut Tape (CT) is the way it's packaged.In the 4-UFBGA, WLCSP package, it is included.The LED driver is mounted as Surface Mount.There is a General Purpose switch type associated with it.To ensure reliable operation, set the temperature to -40°C~125°C TJ.By default, it is set to output 1.To operate, it needs a supply voltage of Not Required.A maximum output voltage of P-Channel volts can be achieved by this LED driver.A lighting driver with Slew Rate Controlled features is available.The ADP198 family consists of this type.A total of 4 terminations can be found in it.For operation, we use the 4 pins.The LED driving board has a total of 1 functions.To comply with the operation criteria, the maximum output current is reduced to 1A.Supply voltages of 2.8V allow for high efficiency.In this case, it is mounted in the way of Surface Mount.4 pins are equipped with it.There is 50mOhm resistance on the LED driver.When this case is used, the output current is set to 1A.Self-contained LED driver with Peripheral Drivers capacity in an econtainer.A 2.8V power supply is used by the part.A supply voltage of 6.5V is recommended for maximum efficiency.There is a maximum input voltage of 6.5V volts.There is a minimum input voltage of 1.65V volts.
ADP198ACBZ-R7 Features
Supplied from 2.8V
Resistance of 50mOhm
ADP198ACBZ-R7 Applications
There are a lot of Analog Devices Inc. ADP198ACBZ-R7 Power Switches ICs applications.
- Smartphone and PDA
- Portable Music Players
- HDD and SSD
- Hot Swaps
- Low Voltage I/O System Power
- Set-Top Boxes
- Wireless/Networking Cards
- Hot-Swap Systems
- Gaming
- Hot Swap
