ADP198ACPZ-R7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-UFDFN Exposed Pad, CSP |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| Feature | Slew Rate Controlled |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 40mOhm |
| Subcategory | Peripheral Drivers |
| Technology | DMOS |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 2.8V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADP198 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Type | P-Channel |
| Max Output Current | 1A |
| Operating Supply Voltage | 6.5V |
| Interface | On/Off |
| Operating Supply Current | 1.1μA |
| Output Configuration | High Side |
| Output Current | 200mA |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Turn On Delay Time | 450 μs |
| Switch Type | General Purpose |
| Min Input Voltage | 1.65V |
| Max Input Voltage | 6.5V |
| Output Current per Channel | 1A |
| Nominal Input Voltage | 6.5V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 1.65V~6.5V |
| Driver Number of Bits | 1 |
| Fault Protection | Reverse Current |
| Rds On (Typ) | 75m Ω |
| Height Seated (Max) | 0.65mm |
| Length | 2mm |
| Width | 2mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADP198ACPZ-R7 Overview
Tape & Reel (TR) is how it's packaged.It is included with the 8-UFDFN Exposed Pad, CSP package as well.This LED driving board is mounted using the mounting type Surface Mount.There is a General Purpose switch type associated with it.It is recommended that the temperature be set to -40°C~125°C TJ for reliable operation.In this LED driver, there are no outputs available.A supply voltage of Not Required is required for it to operate.A maximum output voltage of P-Channel volts has been specified.As far as features are concerned, the LED driving board has Slew Rate Controlled.It is part of the ADP198 family of LED drivers.In total, there are 8 terminations.In order to operate, the 8 pins are used.It consists of 1 functions.This results in the maximum output current dropping to 1A to meet the operation criteria.With a supply voltage of 2.8V, high efficiency is possible.Surface Mount is mounted in the way.8 pins are equipped with it.It has 40mOhm resistance.This case has the output current set to 200mA.A self-contained econtainer holding Peripheral Drivers capacity contains this lighting driver.A supply voltage of 6.5V is recommended for maximum efficiency.A maximum input voltage of 6.5V volts can be applied to it.Input voltage must be at least 1.65V volts.
ADP198ACPZ-R7 Features
Supplied from 2.8V
Resistance of 40mOhm
ADP198ACPZ-R7 Applications
There are a lot of Analog Devices Inc. ADP198ACPZ-R7 Power Switches ICs applications.
- Mobile Communication Devices
- Hot Swaps
- Hot Swap
- PDAs
- Hot Swap
- Handheld Devices
- Notebook and Tablet Computers
- HDD and SSD
- Notebook PC
- Wearable Devices
