ADTL084ARZ
| Parameters | |
|---|---|
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 1.5mV |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Dual Supply Voltage | 15V |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Input Offset Current-Max (IIO) | 0.005μA |
| Input Voltage Noise Density | 16nV/sqrt Hz |
| Height | 1.5mm |
| Length | 8.75mm |
| Width | 4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADTL084 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Number of Channels | 4 |
| Operating Supply Current | 4.8mA |
| Quiescent Current | 1.2mA |
| Slew Rate | 20V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 2pA |
| Voltage - Supply, Single/Dual (±) | 8V~36V ±4V~18V |
| Output Current per Channel | 27mA |
| Input Offset Voltage (Vos) | 5.5mV |
| Bandwidth | 5MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
ADTL084ARZ Overview
There is a 14-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. The instrumentation amplifier in this picture is of the J-FET-type. Upon delivery, op amp ic is packaged in a Tube case. A total of 14 terminations have been reported in the past few weeks. Linear amplifier has a total of 14 pins. As a reminder, this buffer op amp should be powered by 15V battery and that the battery should be inserted in the amplifier. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. In total, the buffer amplifier consists of 14 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 5.5mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . An 4.8mA volt supply current is needed for this linear amplifier to operate. You should keep the voltage gain at 106.02dB for the time being. 4 channels are available on the instrumentation amplifier. Currently, linear amplifier is operating with a quiescent current of 1.2mA.
ADTL084ARZ Features
14 Pins
supply voltage of 15V
106.02dB voltage gain
ADTL084ARZ Applications
There are a lot of Analog Devices Inc. ADTL084ARZ Instrumentational OP Amps applications.
- Medical instruments
- Hand-held batteries
- ECG equipment
- Comparator
- Information processing
- E-book readers
- Medical imaging
- Ultrasound transducers
- MP3
- Test equipment
