AH5794-WU-7
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 26 |
| Operating Temperature | -40°C~105°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 6 |
| Terminal Finish | Matte Tin (Sn) |
| Applications | Fan Motor Driver |
| HTS Code | 8542.39.00.01 |
| Subcategory | Motion Control Electronics |
| Max Power Dissipation | 650mW |
| Technology | Power MOSFET |
| Voltage - Supply | 1.8V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| JESD-30 Code | R-PDSO-G6 |
| Function | Driver - Fully Integrated, Control and Power Stage |
| Output Voltage | 4.8V |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 1.8V |
| Interface | On/Off |
| Analog IC - Other Type | BRUSHLESS DC MOTOR CONTROLLER |
| Operating Supply Current | 2.2mA |
| Output Configuration | Half Bridge (2) |
| Current - Output | 500mA |
| Logic Function | AND |
| Voltage - Load | 1.8V~6V |
| Motor Type - AC, DC | Brushless DC (BLDC) |
| Height | 900μm |
| Length | 3mm |
| Width | 1.7mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
AH5794-WU-7 Overview
There is a Tape & Reel (TR)package included in the design.Drivers controllers is packaged wDrivers controllersh a SOT-23-6 case.Ideally, the part should be mounted by Surface Mount.This component is suitable for the component connected to Fan Motor Driver.There is a possibility of providing 1.8V~6Vvolts through the device.In terms of operating temperature, it falls within the range -40°C~105°C TA.In this case, the motor type is Brushless DC (BLDC).This part provides 6terminations.At a rate of [0], voltage can be applied to the load.Drivers controllers is recommended that this amplifier be run at 5V.Surface Mountis the recommended mounting method.Maintain a current of 500mA for the part output.An analog IC with the model number BRUSHLESS DC MOTOR CONTROLLERis employed in the device.26pins are available on the device.Drivers controllers belongs to the Motion Control Electronics series.At [0], the output voltage is maintained.For its operation, a supply current of 2.2mAis used.
AH5794-WU-7 Features
Applications : Fan Motor Driver
Load voltage across the chip 1.8V~6V
AH5794-WU-7 Applications
There are a lot of Diodes Incorporated AH5794-WU-7 motor drivers applications.
- AM radio
- High brightness LED lighting
- Side marker lights
- Charge pump circuits
- RGB and monochromatic LED drivers for signage and traffic signals
- LED bias
- Large outdoor LED display
- Matrix LED dimmers
- Telltale lights
- Digital still cameras
