Parameters |
Switch-on Time-Max |
130ns |
Switch-off Time-Max |
130ns |
RoHS Status |
ROHS3 Compliant |
Factory Lead Time |
1 Week |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2016 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
135Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
600mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
4 |
Supply Voltage |
5V |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
12V |
Min Supply Voltage |
3V |
Nominal Supply Current |
10nA |
Max Supply Current |
1μA |
Turn On Delay Time |
300 ns |
Voltage - Supply, Single/Dual (±) |
3V~12V ±1.5V~6V |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
6V |
On-State Resistance (Max) |
135Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
3pF 3pF |
On-state Resistance Match-Nom |
16Ohm |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
130ns, 130ns |
Charge Injection |
0.2pC |
Channel-to-Channel Matching (ΔRon) |
2.7 Ω |
Crosstalk |
-90dB @ 100kHz |
ALD4213SCL Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. It is mounted in the position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operation at a temperature around -40°C~85°C TA. In total, 16 terminations have occurred. The electronic part delivers high-quality output through its 1 channels. A 5V voltage supply should turn on and run the electronic component. Based on SPST - NO/NC switching circuits, these analog multiplexers work. This multiplexer is composed of 4 circuits. Internally, this switch multiplexer has a resistance of 135Ohm. The functions of 16 pins can be found in the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. 3V is the lowest voltage that should be fed to the electronic electronic part. The analogue multiplexer may be damaged if voltage is greater than 1μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6V.
ALD4213SCL Features
1 Channels
Switch Circuit: SPST - NO/NC
ALD4213SCL Applications
There are a lot of Advanced Linear Devices Inc. ALD4213SCL Analog Switches & Multiplexers ICs applications.
- Cable PC
- PDAs
- Automatic test equipment
- Frame Relay Equipment
- Power routing
- Fiber In The Loop (FITL)
- FTTH
- RGB switches
- Video switching
- PBXs