banner_page

AP2145SG-13

3/5V P-Channel PMIC 8 Pin 3.3V 8-SOIC (0.154, 3.90mm Width)


  • Manufacturer: Diodes Incorporated
  • Nocochips NO: 233-AP2145SG-13
  • Package: 8-SOIC (0.154, 3.90mm Width)
  • Datasheet: PDF
  • Stock: 868
  • Description: 3/5V P-Channel PMIC 8 Pin 3.3V 8-SOIC (0.154, 3.90mm Width) (Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 8-SOIC (0.154, 3.90mm Width)
Number of Pins 8
Weight 142.994995mg
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2010
JESD-609 Code e3
Feature Status Flag
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 3 (168 Hours)
Number of Terminations 8
ECCN Code EAR99
Resistance 160Ohm
Terminal Finish Matte Tin (Sn)
Subcategory Peripheral Drivers
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 3.3V
Time@Peak Reflow Temperature-Max (s) 40
Pin Count 8
Number of Outputs 1
Output Type P-Channel
Max Output Current 500mA
Supply Voltage-Max (Vsup) 5.5V
Power Supplies 3/5V
Supply Voltage-Min (Vsup) 2.7V
Interface On/Off
Output Configuration High Side
Voltage - Supply (Vcc/Vdd) Not Required
Input Type Non-Inverting
Turn On Delay Time 1.5 ms
Switch Type USB Switch
Turn-Off Delay Time 100 μs
Ratio - Input:Output 1:1
Voltage - Load 2.7V~5.5V
Driver Number of Bits 1
Fault Protection Current Limiting (Fixed), Over Temperature, Reverse Current, UVLO
Output Peak Current Limit-Nom 0.5A
Rds On (Typ) 95m Ω
Built-in Protections TRANSIENT; OVER CURRENT; THERMAL; UNDER VOLTAGE
Output Current Flow Direction SINK
Length 4.9mm
Width 3.9mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant

AP2145SG-13 Overview


As a result, it is packaged in the form of a Tape & Reel (TR).There is a package for it in the 8-SOIC (0.154, 3.90mm Width) package.Surface Mount is the mounting type of the LED driver.USB Switch is the switch type that it owns.It is recommended that the temperature be set to -40°C~85°C TA for reliable operation.The LED driver has 1 outputs.The LED driving board operates at Not Required volts.A maximum output voltage of P-Channel volts can be achieved by this LED driver.In terms of features, the LED driving board has Status Flag.A total of 8 terminations have been found in it.It is necessary to use the 8 pins in order to operate the LED driver.It has 1 functions.As a result, the maximum output current is reduced to 500mA in order to meet the operation requirements.The supply voltage can be 3.3V for high efficiency.The lighting driver is mounted in the way of Surface Mount.The LED driving board is equipped with a total of 8 pins.Currently, the LED driving board has a resistance of 160Ohm ohms.This LED driver is self-contained in an econtainer with a capacity of Peripheral Drivers.The maximum supply voltage for this lighting driver is set to 5.5V (Vsup).Normal operation requires Vsup above 2.7V.A 3/5V power supply is used by the part.

AP2145SG-13 Features


Supplied from 3.3V
Resistance of 160Ohm

AP2145SG-13 Applications


There are a lot of Diodes Incorporated AP2145SG-13 Power Switches ICs applications.

  • Portable Devices
  • PC Cards
  • Hot Swap
  • USB Ports/Hubs
  • Wearable Devices
  • Portable GPS
  • Storage Drives
  • Wireless Headsets
  • Storage (HDDs, SSDs)
  • Hard Disk Drives

Write a review

Note: HTML is not translated!
    Bad           Good