AP2152AFGEG-7
| Parameters | |
|---|---|
| Length | 3.05mm |
| Width | 3.05mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-UDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Published | 2013 |
| JESD-609 Code | e4 |
| Feature | Load Discharge, Status Flag |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 125mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | AP2152 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Output Type | P-Channel |
| Max Output Current | 500mA |
| Number of Channels | 2 |
| Interface | On/Off |
| Analog IC - Other Type | POWER SUPPLY SUPPORT CIRCUIT |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Adjustable Threshold | NO |
| Input Type | Non-Inverting |
| Switch Type | USB Switch |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Ratio - Input:Output | 1:2 |
| Voltage - Load | 2.7V~5.5V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Reverse Current, UVLO |
| Rds On (Typ) | 85m Ω |
| Height | 580μm |
AP2152AFGEG-7 Overview
The LED driver's packaged as a Cut Tape (CT).The 8-UDFN Exposed Pad package contains it.A Surface Mount mounting is used for the LED driving board.There is a switch type of USB Switch.Ensure reliable operation by setting the temperature to -40°C~85°C TA.The lighting driver has a total of 2 outputs that are available for use.A supply voltage of Not Required is required for it to operate.It produces a maximum output voltage of P-Channel volts at its maximum output.The lighting driver has Load Discharge, Status Flag features.It is a member of the AP2152 family.It consists of 8 terminations in total.It is necessary to use the 8 pins in order to operate the LED driver.As far as the lighting driver is concerned, there are 1 functions.This results in the maximum output current dropping to 500mA to meet the operation criteria.A supply voltage of 5V leads to high efficiency.As a result, it is mounted in the manner of Surface Mount.In total, it has 8 pins.In this LED driving board, there is 125mOhm resistance.There is an analog input IC in this gadget, which is POWER SUPPLY SUPPORT CIRCUIT.In total, there are 2 channels available.This LED driving board can accept voltages up to 5.5V volts as an input.As far as input voltage goes, it has a minimum of 2.7V volts.
AP2152AFGEG-7 Features
Supplied from 5V
Resistance of 125mOhm
2 channels
AP2152AFGEG-7 Applications
There are a lot of Diodes Incorporated AP2152AFGEG-7 Power Switches ICs applications.
- Solid State Drivers
- Smart Phones, Feature Phones
- Storage (HDDs, SSDs)
- Low Voltage I/O System Power
- Wearable Devices
- PDAs
- USB3.1 Power Delivery
- Portable Devices
- Portable/Handheld Devices
- USB Power Distribution
