AP2152MPG-13
| Parameters | |
|---|---|
| Output Current Flow Direction | SINK |
| Height | 950μm |
| Length | 3.1mm |
| Width | 3.05mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Number of Pins | 8 |
| Weight | 139.989945mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2014 |
| JESD-609 Code | e3 |
| Feature | Status Flag |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 150MOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Peripheral Drivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Current Rating | 800mA |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AP2152 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Output Type | P-Channel |
| Max Output Current | 500mA |
| Power Supplies | 3/5V |
| Interface | On/Off |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | USB Switch |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Ratio - Input:Output | 1:2 |
| Voltage - Load | 2.7V~5.5V |
| Driver Number of Bits | 2 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Reverse Current, UVLO |
| Turn On Time | 50 μs |
| Output Peak Current Limit-Nom | 0.5A |
| Rds On (Typ) | 115m Ω |
| Turn Off Time | 10 μs |
| Built-in Protections | TRANSIENT; OVER CURRENT; THERMAL; UNDER VOLTAGE |
AP2152MPG-13 Overview
A Tape & Reel (TR) is used to package it.The 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad package contains it.This LED driving board is mounted using the mounting type Surface Mount.There is a USB Switch switch type associated with it.To ensure reliable operation, the temperature should be set to -40°C~85°C TA.It is possible to use 2 outputs in the lighting driver.To operate, it needs a supply voltage of Not Required.A maximum output voltage of P-Channel volts has been specified.Currently, the LED driving board is equipped with Status Flag features.The AP2152 family contains this object.It contains 8 terminations.For operation, we use the 8 pins.It contains 2 functions.This operation requires the maximum output current to be decreased to 500mA.The supply voltage of 5V is conducive to high efficiency.Surface Mount is mounted in the way of this LED driving board.In total, it has 8 pins.Currently, the LED driving board has a resistance of 150MOhm ohms.The LED driver is self-contained in an econtainer with Peripheral Drivers capacity.3/5V is the power supply of the part.The maximum input voltage of the LED driver is 5.5V volts.There is a minimum input voltage of 2.7V volts.
AP2152MPG-13 Features
Supplied from 5V
Resistance of 150MOhm
AP2152MPG-13 Applications
There are a lot of Diodes Incorporated AP2152MPG-13 Power Switches ICs applications.
- USB Power Distribution
- USB Ports/Hubs
- Portable GPS
- Mobile Communication Devices
- Wireless/Networking Cards
- USB Protection
- PDAs
- Hard Disk Drives
- Hot Swap
- Smartphone and PDA
