AP2155SG-13
| Parameters | |
|---|---|
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 142.994995mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Feature | Status Flag |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 160Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Peripheral Drivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Max Output Current | 500mA |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3/5V |
| Supply Voltage-Min (Vsup) | 2.7V |
| Interface | On/Off |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Turn On Delay Time | 1.5 ms |
| Switch Type | USB Switch |
| Turn-Off Delay Time | 100 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~5.5V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Reverse Current, UVLO |
| Output Peak Current Limit-Nom | 0.5A |
| Rds On (Typ) | 95m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
AP2155SG-13 Overview
It's?packaged?in?the way?of?a?Tape & Reel (TR).It is included in the package 8-SOIC (0.154, 3.90mm Width).It has been mounted as Surface Mount on the LED driver.It owns the USB Switch switch type.It is recommended that the temperature be set to -40°C~85°C TA for reliable operation.The LED driver is equipped with 1 outputs.It uses a supply voltage of Not Required to operate.It produces a maximum output voltage of P-Channel volts at its maximum output.The lighting driver has Status Flag features.The termination count is 8.In order to operate, 8 pins are used.Currently, the lighting driver has a total of 1 functions.The maximum output current must drop to 500mA to meet the operation criteria.High efficiency is possible when the supply voltage is set to 3.3V.Surface Mount is mounted in the way.8 pins are connected to it in total.In this case, there is 160Ohm resistance in the LED driving board.The LED driver is self-contained in an econtainer with Peripheral Drivers capacity.This LED driver is configured to have a maximum supply voltage of 5.5V (Vsup).In order for this lighting driver to operate normally, the supply voltage (Vsup) should remain above 2.7V.There is a voltage supply of 3/5V volts on this part.
AP2155SG-13 Features
Supplied from 3.3V
Resistance of 160Ohm
AP2155SG-13 Applications
There are a lot of Diodes Incorporated AP2155SG-13 Power Switches ICs applications.
- Portable/Handheld Devices
- HDD and SSD
- Storage (HDDs, SSDs)
- Gaming
- Hot-Swap Systems
- Set-Top Boxes
- Solid State Drivers
- Telecom and Network Systems
- Portable Devices
- Handheld Devices
