AP2162AMPG-13
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Feature | Load Discharge, Status Flag |
| Pbfree Code | yes |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 125mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Output Type | P-Channel |
| Max Output Current | 1A |
| Supply Voltage-Max (Vsup) | 5.5V |
| Number of Channels | 2 |
| Interface | On/Off |
| Analog IC - Other Type | POWER SUPPLY SUPPORT CIRCUIT |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Adjustable Threshold | NO |
| Input Type | Non-Inverting |
| Switch Type | USB Switch |
| Ratio - Input:Output | 1:2 |
| Voltage - Load | 2.7V~5.5V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Reverse Current, UVLO |
| Rds On (Typ) | 85m Ω |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
AP2162AMPG-13 Overview
It is packaged in the form of a Cut Tape (CT).In the 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad package, it is included.Mounting type Surface Mount is selected for the LED driving board.It owns USB Switch switch type.It is recommended that the temperature be set to -40°C~85°C TA for reliable performance.The LED driver is equipped with 2 outputs.A supply voltage of Not Required is required for it to operate.A maximum output voltage of P-Channel volts can be achieved by this LED driver.As far as features are concerned, the LED driving board has Load Discharge, Status Flag.It contains 8 terminations.During operation, the 8 pins are used.It consists of 1 functions.This operation requires the maximum output current to be decreased to 1A.With a supply voltage of 5V, high efficiency is possible.In this case, it is mounted in the way of Surface Mount.This LED driver is equipped with a total of 8 pins.In this LED driving board, there is 125mOhm resistance.The maximum supply voltage is set to 5.5V.The gadget uses an analog IC, which is POWER SUPPLY SUPPORT CIRCUIT in this case.We offer 2 channels in total.
AP2162AMPG-13 Features
Supplied from 5V
Resistance of 125mOhm
2 channels
AP2162AMPG-13 Applications
There are a lot of Diodes Incorporated AP2162AMPG-13 Power Switches ICs applications.
- Portable Music Players
- Storage Drives
- Wireless/Networking Cards
- Wireless Headsets
- Portable/Handheld Devices
- Portable GPS Device
- Wearable Devices
- Hot Swap
- Notebook PC
- Solid-State Drives
