Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Number of Pins |
8 |
Weight |
850.995985mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2009 |
JESD-609 Code |
e3 |
Feature |
Status Flag |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
3 (168 Hours) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
160MOhm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Peripheral Drivers |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
5V |
Current Rating |
1.5A |
Time@Peak Reflow Temperature-Max (s) |
40 |
Pin Count |
8 |
Number of Outputs |
2 |
Output Type |
P-Channel |
Max Output Current |
1A |
Supply Voltage-Max (Vsup) |
5.5V |
Power Supplies |
3/5V |
Interface |
On/Off |
Output Configuration |
High Side |
Voltage - Supply (Vcc/Vdd) |
Not Required |
Input Type |
Non-Inverting |
Switch Type |
USB Switch |
Ratio - Input:Output |
1:2 |
Voltage - Load |
2.7V~5.5V |
Driver Number of Bits |
2 |
Fault Protection |
Current Limiting (Fixed), Over Temperature, Reverse Current, UVLO |
Turn On Time |
50 μs |
Output Peak Current Limit-Nom |
1A |
Turn Off Time |
10 μs |
Built-in Protections |
TRANSIENT; OVER CURRENT; THERMAL; UNDER VOLTAGE |
Output Current Flow Direction |
SINK |
Height Seated (Max) |
1.75mm |
Length |
4.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
AP2162SG-13 Overview
A Tape & Reel (TR) is used to package it.The 8-SOIC (0.154, 3.90mm Width) package includes it.The LED driver is mounted as Surface Mount.The switch type of this switch is USB Switch.It is recommended that the temperature be set to -40°C~85°C TA for reliable operation.In this LED driver, there are no outputs available.Operation is based on a supply voltage of Not Required.It has a maximum output voltage of P-Channel volts.There are Status Flag features available on the LED driving board.A total of 8 terminations have been found in it.In order to operate, the 8 pins are used.It contains 2 functions.To comply with the operation criteria, the maximum output current is reduced to 1A.With a supply voltage of 5V, high efficiency is possible.Surface Mount is mounted in the way of this lighting driver.It is equipped with a total of 8 pins.There is 160MOhm resistance on the LED driver.Self-contained in an econtainer with a capacity of Peripheral Drivers, this LED driver is self-contained.This LED driver is configured to have a maximum supply voltage of 5.5V (Vsup).This part has a power supply of 3/5V.
AP2162SG-13 Features
Supplied from 5V
Resistance of 160MOhm
AP2162SG-13 Applications
There are a lot of Diodes Incorporated AP2162SG-13 Power Switches ICs applications.
- USB Power Distribution
- Notebook and Tablet Computers
- Portable GPS Device
- HDD and SSD
- Wireless Headsets
- Wireless/Networking Cards
- Wearable Devices
- Hot-Swap Systems
- Low Voltage I/O System Power
- HDD, SSD