AP2171SG-13
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 850.995985mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Feature | Status Flag |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 115MOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Peripheral Drivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Current Rating | 1.5A |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Max Output Current | 1A |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3/5V |
| Supply Voltage-Min (Vsup) | 2.7V |
| Interface | On/Off |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | USB Switch |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~5.5V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Reverse Current, UVLO |
| Output Peak Current Limit-Nom | 1.2A |
| Rds On (Typ) | 95m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
AP2171SG-13 Overview
As you can see, it's packaged in the way of a Tape & Reel (TR).This file is included in package 8-SOIC (0.154, 3.90mm Width).This lighting drivere has a mounting type of Surface Mount.There is a USB Switch switch type associated with it.In order to guarantee reliable performance, the temperature should be set to -40°C~85°C TA.The LED driver has 1 outputs.The LED driving board is powered by a voltage of Not Required.Voltage output is P-Channel volts at maximum.Currently, the LED driving board is equipped with Status Flag features.A total of 8 terminations have been recorded.During operation, the 8 pins are used.As far as functions are concerned, the lighting driver has 1.Maximum output current falls to 1A when operation criteria are met.Using a voltage of 5V allows for high efficiency.Surface Mount is mounted in the way.As a result, it has a total of 8 pins.Currently, the LED driving board has a resistance of 115MOhm ohms.A self-contained LED driver with a capacity of Peripheral Drivers is contained in an econtainer.The Vsup value (maximum supply voltage) is set to 5.5V.In order for this lighting driver to operate normally, the supply voltage (Vsup) should remain above 2.7V.This part's power supply is 3/5V.
AP2171SG-13 Features
Supplied from 5V
Resistance of 115MOhm
AP2171SG-13 Applications
There are a lot of Diodes Incorporated AP2171SG-13 Power Switches ICs applications.
- Portable/Handheld Devices
- USB Protection
- Wireless Headsets
- Portable Music Players
- USB Power Distribution
- Set-top-box
- Low Voltage I/O System Power
- Notebook PC
- Hot-Swap Systems
- Telecom and Network Systems
