AP2191SG-13
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 73.992255mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2015 |
| JESD-609 Code | e3 |
| Feature | Status Flag |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 115mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Peripheral Drivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Current Rating | 2.1A |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AP2191 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Max Output Current | 1.5A |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3/5V |
| Supply Voltage-Min (Vsup) | 2.7V |
| Interface | On/Off |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | USB Switch |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~5.5V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Reverse Current, UVLO |
| Output Peak Current Limit-Nom | 2A |
| Rds On (Typ) | 95m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
AP2191SG-13 Overview
It is packaged in the form of a Tape & Reel (TR).It's included in the 8-SOIC (0.154, 3.90mm Width) package.It has been mounted as Surface Mount on the LED driver.USB Switch is the switch type that it owns.To ensure reliable performance, the temperature should be set to -40°C~85°C TA.In this LED driver, there are no outputs available.With a supply voltage of Not Required, the LED driving board operates.It produces a maximum output voltage of P-Channel volts at its maximum output.It is equipped with Status Flag features.I believe it belongs to the AP2191 family.A total of 8 terminations have been found in it.The 8 pins are used for the operation of the system.It has 1 functions.In order to meet the operation criteria, the maximum output current drops to 1.5A.It is possible to achieve a high level of efficiency with a supply voltage of 5V.This lighting driver is mounted in the way of Surface Mount.This LED driver is equipped with a total of 8 pins.Lighting drivers with 115mOhm resistance are used.There is a Peripheral Drivers capacity container for this LED driver that is self-contained.In this LED driver, the maximum supply voltage is configured to be 5.5V (Vsup).In order for this lighting driver to operate normally, the supply voltage (Vsup) should remain above 2.7V.In this part, the power supply is set to 3/5V.
AP2191SG-13 Features
Supplied from 5V
Resistance of 115mOhm
AP2191SG-13 Applications
There are a lot of Diodes Incorporated AP2191SG-13 Power Switches ICs applications.
- USB Power Distribution
- PC Cards
- Storage (HDDs, SSDs)
- Hard Disk Drives
- Hot Swap
- USB Protection
- Notebook PC
- PC Card Hot Swap
- Portable/Handheld Devices
- Hot-Swap Systems
