AP3595FNTR-G1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-VFQFN Exposed Pad |
| Number of Pins | 24 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2014 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | QUAD |
| Terminal Pitch | 0.5mm |
| Function | Step-Down |
| Number of Outputs | 2 |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 13.2V |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | DUAL SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 60A |
| Voltage - Supply (Vcc/Vdd) | 10.8V~13.2V |
| Control Features | Enable, Frequency Control, Phase Control, Soft Start |
| Input Voltage (Min) | 10.8V |
| Topology | Buck |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 50kHz~1MHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Max Duty Cycle | 40 % |
| Clock Sync | No |
| Height Seated (Max) | 0.8mm |
| Length | 4mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
AP3595FNTR-G1 Overview
Capsuled in the 24-VFQFN Exposed Pad package, the switching controller can be used for a wide range of applications. dc motor controller is suitable for 2 output generation. PMIC is packaged in a solid enclosure of Tape & Reel (TR). There are Transistor Driver dc switching's output (s) that it can handle. dc control's supply and operating voltages are 10.8V~13.2V. Worked in an dc switcher with a -40°C~85°C TA rating. The switching controller can be switched at 50kHz~1MHz. It is suitable for general dc dc regulator when it is set to Surface Mount. Featured in the dcdc regulator is Enable, Frequency Control, Phase Control, Soft Start which allows efficient switching control. A DUAL SWITCHING CONTROLLER analog integrated circuit is connected to the switch converters. A switching converters's terminal (s) sits at the QUAD position. Different dc switching's functions can be applied to 24 terminations. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. DC switcher's input voltageis 12V volts. In total, switching converter has 24 pins. Switching converter is a type of Switching Regulator or Controllers in particular. It is recommended to use 10.8V as the minimum input voltage of dc dc voltage regulator. normally, the dc dc regulator's output current is 60A, which you should keep in mind when starting a project. voltage regulator dc to dcs with a 40 % duty cycle are designed to be reliable when powered on and powered off. Having a Surface Mount makes DC switcher ideal for most prototype and application designs. In order for the voltage regulator dc to dc to perform safely and reliably in a circuit, users are advised to apply 13.2V.
AP3595FNTR-G1 Features
Transistor Driver Outputs
Switching Frequency: 50kHz~1MHz
Enable, Frequency Control, Phase Control, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 40 %
AP3595FNTR-G1 Applications
There are a lot of Diodes Incorporated AP3595FNTR-G1 DC to DC converter applications.
- Medical equipment
- Access control systems
- Network technology
- Household control circuits
- Industrial robots
- Emergency lighting monitoring equipment
- Direct power supply system
- Solar power plants
- Television equipment
- Photovoltaic power
