APX358SG-13
| Parameters | |
|---|---|
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | APX358 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Operating Supply Current | 190μA |
| Supply Current-Max | 0.6mA |
| Slew Rate | 1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 15nA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Output Current per Channel | 90mA |
| Supply Type | Single |
| Input Offset Voltage (Vos) | 7mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Power Supply Rejection Ratio (PSRR) | 50dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 5.5V |
| Voltage - Input Offset | 1.7mV |
| Low-Bias | NO |
| Micropower | YES |
| Programmable Power | NO |
| Input Voltage Noise Density | 23nV/sqrt Hz |
| Height | 1.5mm |
| Length | 4.95mm |
| Width | 3.95mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 850.995985mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
APX358SG-13 Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. A General Purpose-type buffer amplifier is shown here. Linear amplifier is delivered in a Tape & Reel (TR) case. It is estimated that there will be at least 8 terminations this year. It consists of a total of 8 pins in total. As a reminder, this buffer op amp should be powered by 2.7V battery and that the battery should be inserted in the amplifier. Instrumentation amplifier is a part of Operational Amplifier. An 8-pin op amp ic is included in the package. With regards to the offset voltage of the input, buffer amplifier is rated at 7mV. This electronic part is best mounted with type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. As long as the supply current of the chip does not exceed 190μA, this op amp ic can operate. You should keep the voltage gain at 100dB for the time being. On the buffer amps, there are 2 channels that can be used. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. TAPE AND REEL is adopted to pack the instrumentation amplifier.
APX358SG-13 Features
8 Pins
supply voltage of 2.7V
100dB voltage gain
Output Type: Rail-to-Rail
APX358SG-13 Applications
There are a lot of Diodes Incorporated APX358SG-13 Instrumentational OP Amps applications.
- RF cable systems
- E-book readers
- Ultrasound transducers
- Vehicle electronics
- Wireless base stations
- Video data acquisition
- Logarithmic operation circuits
- Precision measurement
- Multiplication circuits
- Broadcasting
