APX803-26SAG-7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-236-3, SC-59, SOT-23-3 |
| Number of Pins | 3 |
| Weight | 7.994566mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 400mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 0.96mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | APX803 |
| Output | Open Drain or Open Collector |
| Pin Count | 3 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.1V |
| Operating Supply Current | 20μA |
| Power Dissipation | 400mW |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 2.59V |
| Max Reset Threshold Voltage | 2.66V |
| Threshold Voltage | +2.63V |
| Overvoltage Threshold | 2.63V |
| Number of Monitored Inputs | 4 |
| Reset Delay Time | 200 ms |
| Height | 1mm |
| Length | 3mm |
| Width | 1.4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
APX803-26SAG-7 Overview
A total of 3 terminals are used to mount this power management. Packaged in a Cut Tape (CT)-shape, IC management comes with a number of features. To assist you, this IC power includes 1 functions. There are 1 channels on this power managment ic that can be found in a series. In this IC management you will find TO-236-3, SC-59, SOT-23-3 functions for you to refer to. Several of the benefits of this PMIC are also shared by other Simple Reset/Power-On Reset products. As specified in the package specification, the peak reflow temperature of the package is set at 260. When 1 is applied to the power ic, it conducts. Surface Mount mounts power management on the wall. A IC power such as this can be classified as a Power Management Circuits power management system. There are a total of 3 pins on power management. 3 pins make up the power management. It is recommended that Vsup should not be less than 1.1V for this IC power. The maximum supply voltage (Vsup) in this PMIC should not exceed 5.5V volts. The recommended mounting type for IC management is Surface Mount. It is recommended to set the supervisor's temperature to this range: -40°C~85°C TA. As this power managment ic operates, it is able to produce an output voltage of Open Drain or Open Collector. For this power management, there is an 20μA volt supply current. It is always advisable to use APX803, the base supervisor number, when searching for similar PMICs from the manufacturer. There are a total of 4 monitored inputs on the power management.
APX803-26SAG-7 Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.1V
20μA operating supply current
APX803-26SAG-7 Applications
There are a lot of Diodes Incorporated APX803-26SAG-7 Voltage Supervisors applications.
- Stable power system
- emergency room
- Power distribution systems of operating room
- Automotive permanent magnet synchronous motors
- Sensitive sensors
- Digitally controlled LDO regulators circuit
- Dash board
- Telecommunications equipment
- Urban rail transit weak current power monitoring
- Military electronics
