APX803-31SRG-7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-236-3, SC-59, SOT-23-3 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 400mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 0.96mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | APX803 |
| Output | Open Drain or Open Collector |
| Pin Count | 3 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.1V |
| Operating Supply Current | 20μA |
| Power Dissipation | 400mW |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 3.04V |
| Max Reset Threshold Voltage | 3.13V |
| Threshold Voltage | +3.08V |
| Overvoltage Threshold | 3.08V |
| Number of Monitored Inputs | 4 |
| Reset Delay Time | 200 ms |
| Height | 1mm |
| Length | 3mm |
| Width | 1.4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
APX803-31SRG-7 Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 3 in total. Packaged in a Cut Tape (CT)-shape, IC management comes with a number of features. For your reference, this IC power includes a list of 1 functions. A series of 1 channels can be found on this supervisor. Please refer to power management for TO-236-3, SC-59, SOT-23-3 functions. Compared to other Simple Reset/Power-On Reset products, this PMIC has a lot of benefits to offer. Specifies a reflow peak temperature of 260 for the package during reflow. Power management conducts at a voltage of 1. Surface Mount is the one that mounts power management. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. It has a total of 3 pins that are attached to IC management. Power managment ic pin count is 3. It is recommended that Vsup should not be less than 1.1V for this IC power. It is recommended that the maximum supply voltage (Vsup) in this IC power be no more than 5.5V volts. A Surface Mount mounting type is recommended. It is recommended that the supervisor be set to this temperature: -40°C~85°C TA. During operation, this power management system outputs Open Drain or Open Collector. It is estimated that the voltage supervisor's supply current is 20μA. A similar IC managements number of the manufacturer can always be found by using APX803, the base power ics number. It is possible to monitor 4 inputs at the same time on the power management as a whole.
APX803-31SRG-7 Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.1V
20μA operating supply current
APX803-31SRG-7 Applications
There are a lot of Diodes Incorporated APX803-31SRG-7 Voltage Supervisors applications.
- Battery cars
- Important electronics for automotive safety
- Magnetic resonance imaging
- Insulation fault location system
- Urban rail transit weak current power monitoring
- DC stabilized power supply module
- Power distribution systems of operating room
- Electrical fire monitoring system
- Dash board
- Kitchen appliances
