AUIPS1011S
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-3, D2Pak (2 Leads + Tab), TO-263AB |
| Number of Pins | 3 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Published | 2014 |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 2 |
| ECCN Code | EAR99 |
| Resistance | 10mOhm |
| Terminal Finish | Matte Tin (Sn) - with Nickel (Ni) barrier |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 3.1W |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 14V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AUIPS1011S |
| JESD-30 Code | R-PSSO-G2 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 6.5A |
| Power Supplies | 6/28V |
| Voltage | 5.5V |
| Interface | On/Off |
| Current | 6.5A |
| Output Configuration | Low Side |
| Power Dissipation | 3.1W |
| Output Current | 6.5A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Clamping Voltage | 39V |
| Nominal Input Voltage | 6V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 36V Max |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Fixed), Over Temperature |
| Rds On (Typ) | 10m Ω |
| Turn Off Time | 700 μs |
| Built-in Protections | TRANSIENT; OVER CURRENT; THERMAL |
| Height | 2.39mm |
| Length | 6.73mm |
| Width | 6.22mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
AUIPS1011S Overview
As a result, it is packaged in the form of a Tube.In the TO-263-3, D2Pak (2 Leads + Tab), TO-263AB package, it is included.In this case, the LED driving board is mounted as Surface Mount.A General Purpose switch type is owned by it.It is recommended that the temperature be set to -40°C~150°C TJ for reliable operation.The lighting driver is equipped with 1 outputs that can be used.The LED driving board operates with a supply voltage of Not Required.A maximum output voltage of N-Channel volts has been specified.As you can see, it comes from the AUIPS1011S family.It consists of 2 terminations in total.It is necessary to use the 3 pins in order to operate the LED driver.As far as the lighting driver is concerned, there are 1 functions.In order to meet the operation criteria, the maximum output current drops to 6.5A.It is possible to achieve a high level of efficiency with a supply voltage of 14V.Surface Mount is mounted in the way of this LED driving board.The LED driver has 10mOhm resistance.It belongs to the Automotive, AEC-Q100 series.The output current is set to 6.5A in this case.This LED driver is self-contained in an econtainer with a capacity of Peripheral Drivers.A 6/28V power supply is used by the part.
AUIPS1011S Features
Supplied from 14V
Resistance of 10mOhm
AUIPS1011S Applications
There are a lot of Infineon Technologies AUIPS1011S Power Switches ICs applications.
- PDAs
- Set-Top Boxes
- Hot Swap
- Solid State Drivers
- Mobile Communication Devices
- Hard Disk Drives
- HDD, SSD
- USB Protection
- Portable GPS Device
- Portable Devices
