banner_page

AUIPS1011STRL

6/28V N-Channel 2.54mm PMIC Automotive, AEC-Q100 Series AUIPS1011S 3 Pin 14V TO-263-3, D2Pak (2 Leads + Tab), TO-263AB


  • Manufacturer: Infineon Technologies
  • Nocochips NO: 376-AUIPS1011STRL
  • Package: TO-263-3, D2Pak (2 Leads + Tab), TO-263AB
  • Datasheet: PDF
  • Stock: 220
  • Description: 6/28V N-Channel 2.54mm PMIC Automotive, AEC-Q100 Series AUIPS1011S 3 Pin 14V TO-263-3, D2Pak (2 Leads + Tab), TO-263AB (Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case TO-263-3, D2Pak (2 Leads + Tab), TO-263AB
Number of Pins 3
Operating Temperature -40°C~150°C TJ
Packaging Tape & Reel (TR)
Published 2009
Series Automotive, AEC-Q100
JESD-609 Code e3
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 2
ECCN Code EAR99
Terminal Finish Matte Tin (Sn) - with Nickel (Ni) barrier
Subcategory Peripheral Drivers
Max Power Dissipation 25W
Terminal Position SINGLE
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 14V
Terminal Pitch 2.54mm
Time@Peak Reflow Temperature-Max (s) 30
Base Part Number AUIPS1011S
JESD-30 Code R-PSSO-G2
Number of Outputs 1
Output Voltage 36V
Output Type N-Channel
Max Output Current 6.5A
Supply Voltage-Max (Vsup) 28V
Power Supplies 6/28V
Supply Voltage-Min (Vsup) 6V
Interface On/Off
Nominal Supply Current 1mA
Output Configuration Low Side
Power Dissipation 3.1W
Output Current 6.5A
Voltage - Supply (Vcc/Vdd) Not Required
Input Type Non-Inverting
Switch Type General Purpose
Rise Time 100μs
Fall Time (Typ) 150 μs
Ratio - Input:Output 1:1
Voltage - Load 36V Max
Driver Number of Bits 1
Fault Protection Current Limiting (Fixed), Over Temperature
Rds On (Typ) 10m Ω
Turn Off Time 700 μs
Built-in Protections TRANSIENT; OVER CURRENT; THERMAL
Width 9.08mm
Radiation Hardening No
RoHS Status RoHS Compliant

AUIPS1011STRL Overview


It is packaged in the form of a Tape & Reel (TR).This file is included in package TO-263-3, D2Pak (2 Leads + Tab), TO-263AB.The lighting driver is mounted in the Surface Mount position.This switch is of type General Purpose.Keeping the temperature at -40°C~150°C TJ ensures reliable operation.In this LED driver, there are no outputs available.A voltage of Not Required is used to power it.Voltage output is N-Channel volts at maximum.The AUIPS1011S family consists of this type.It contains 2 terminations.For operation, 3 pins are used.It contains 1 functions.This operation requires the maximum output current to be decreased to 6.5A.Supply voltages of 14V allow for high efficiency.Surface Mount is mounted in the way.It is included in the Automotive, AEC-Q100 series.In this case, the output current will be set to 6.5A.A container with a capacity of Peripheral Drivers contains this self-contained lighting driver.A maximum supply voltage of 28V is set in Vsup.In order for this lighting driver to operate normally, the supply voltage (Vsup) should remain above 6V.In this case, the power supply is 6/28V.

AUIPS1011STRL Features


Supplied from 14V

AUIPS1011STRL Applications


There are a lot of Infineon Technologies AUIPS1011STRL Power Switches ICs applications.

  • Portable Devices
  • Wireless Modem Data Cards
  • PC Card Hot Swap
  • Telecom and Network Systems
  • Portable GPS
  • Hard Disk Drives
  • Hot-Swap Systems
  • Portable GPS Device
  • Low Voltage I/O System Power
  • Wireless/Networking Cards

Write a review

Note: HTML is not translated!
    Bad           Good