AUIPS1031RTRL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-252-3, DPak (2 Leads + Tab), SC-63 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Resistance | 50MOhm |
| Terminal Finish | Matte Tin (Sn) - with Nickel (Ni) barrier |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 2.5W |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 14V |
| Terminal Pitch | 2.29mm |
| Current Rating | 4A |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AUIPS1031R |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 3A |
| Supply Voltage-Max (Vsup) | 28V |
| Power Supplies | 6/28V |
| Supply Voltage-Min (Vsup) | 6V |
| Interface | On/Off |
| Output Configuration | Low Side |
| Output Current | 3A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 36V Max |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Fixed), Over Temperature |
| Rds On (Typ) | 40m Ω |
| Turn Off Time | 200 μs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Length | 6.54mm |
| Width | 6.095mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
AUIPS1031RTRL Overview
As you can see, it's packaged in the way of a Tape & Reel (TR).There is a TO-252-3, DPak (2 Leads + Tab), SC-63 package that includes it.This lighting drivere has a mounting type of Surface Mount.General Purpose is the type of switch owned by it.It is recommended that the temperature be set to -40°C~150°C TJ for reliable performance.There is a default setting of 1 for output.A voltage of Not Required is used to power it.A maximum output voltage of N-Channel volts has been specified.It comes under the family of AUIPS1031R.As a result, there are 3 terminations.For operation, 3 pins are used.It has 1 functions.As a result, the maximum output current is reduced to 3A in order to meet the operation requirements.High efficiency is possible at 14V supply voltage.Surface Mount is mounted in the way of this lighting driver.Currently, the LED driving board has a resistance of 50MOhm ohms.The Automotive, AEC-Q100 series includes this electrical component.When this is the case, the output current is set to 3A.This LED driver is self-contained in an econtainer with a capacity of Peripheral Drivers.The maximum supply voltage for this lighting driver is set to 28V (Vsup).In order for the lighting driver to operate normally, the supply voltage (Vsup) should be maintained above 6V.The power supply of the part is 6/28V.
AUIPS1031RTRL Features
Supplied from 14V
Resistance of 50MOhm
AUIPS1031RTRL Applications
There are a lot of Infineon Technologies AUIPS1031RTRL Power Switches ICs applications.
- Portable GPS
- Notebook and Tablet Computers
- Portable Music Players
- Portable Video Game Players
- Hot Swap
- Handheld Devices
- Storage Drives
- Smart Phones, Feature Phones
- Storage (HDDs, SSDs)
- Solid State Drivers
