banner_page

AUIPS1041LTR

6/28V N-Channel 2.3mm PMIC Automotive, AEC-Q100 Series AUIPS1041L 4 Pin 14V TO-261-4, TO-261AA


  • Manufacturer: Infineon Technologies
  • Nocochips NO: 376-AUIPS1041LTR
  • Package: TO-261-4, TO-261AA
  • Datasheet: PDF
  • Stock: 395
  • Description: 6/28V N-Channel 2.3mm PMIC Automotive, AEC-Q100 Series AUIPS1041L 4 Pin 14V TO-261-4, TO-261AA (Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case TO-261-4, TO-261AA
Number of Pins 4
Operating Temperature -40°C~150°C TJ
Packaging Tape & Reel (TR)
Published 2012
Series Automotive, AEC-Q100
JESD-609 Code e3
Part Status Obsolete
Moisture Sensitivity Level (MSL) 2 (1 Year)
Number of Terminations 4
ECCN Code EAR99
Resistance 80mOhm
Terminal Finish Matte Tin (Sn)
Subcategory Peripheral Drivers
Max Power Dissipation 2W
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 14V
Terminal Pitch 2.3mm
Current Rating 1.5A
Time@Peak Reflow Temperature-Max (s) 30
Base Part Number AUIPS1041L
Number of Outputs 1
Qualification Status Not Qualified
Output Type N-Channel
Max Output Current 1.5A
Supply Voltage-Max (Vsup) 28V
Power Supplies 6/28V
Supply Voltage-Min (Vsup) 6V
Interface On/Off
Output Configuration Low Side
Voltage - Supply (Vcc/Vdd) Not Required
Input Type Non-Inverting
Turn On Delay Time 15 μs
Switch Type General Purpose
Clamping Voltage 39V
Rise Time 7μs
Fall Time (Typ) 10 μs
Nominal Input Voltage 6V
Turn-Off Delay Time 150 μs
Ratio - Input:Output 1:1
Voltage - Load 6V~28V
Driver Number of Bits 1
Fault Protection Current Limiting (Fixed), Over Temperature
Rds On (Typ) 80m Ω
Drain to Source Resistance 80mOhm
Built-in Protections TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL
Output Current Flow Direction SINK
Length 6.5mm
Width 3.5mm
REACH SVHC No SVHC
RoHS Status RoHS Compliant
Lead Free Lead Free

AUIPS1041LTR Overview


It is package in Tape & Reel (TR) case.This package is included in TO-261-4, TO-261AA.Mounting type Surface Mount is selected for the LED driving board.General Purpose is the switch type that it owns.To ensure reliable performance, the temperature should be set to -40°C~150°C TJ.There are 1 outputs available on this lighting driver.Operation is based on Not Required supply voltage.A maximum output voltage of N-Channel volts can be achieved by this LED driver.It belongs to the family AUIPS1041L.The termination count is 4.In order to operate, the 4 pins are used.It is important to note that the LED driving board has 1 functions.To comply with the operation criteria, the maximum output current is reduced to 1.5A.A supply voltage of 14V leads to high efficiency.Surface Mount is mounted in the way.80mOhm resistance is present in the lighting driver.It is part of the Automotive, AEC-Q100 series.There is a Peripheral Drivers capacity container for this LED driver that is self-contained.Vsup (maximum supply voltage) is set to 28V.In order for this lighting driver to operate normally, the supply voltage (Vsup) should remain above 6V.In this case, the power supply is 6/28V.

AUIPS1041LTR Features


Supplied from 14V
Resistance of 80mOhm

AUIPS1041LTR Applications


There are a lot of Infineon Technologies AUIPS1041LTR Power Switches ICs applications.

  • Portable Devices
  • Smart Phones, Feature Phones
  • Solid State Drivers
  • Hard Disk Drives
  • Wireless/Networking Cards
  • PC Cards
  • PC Card Hot Swap
  • Portable GPS Device
  • Low Voltage I/O System Power
  • Handheld Devices

Write a review

Note: HTML is not translated!
    Bad           Good