AUIPS7145R
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | TO-252-5, DPak (4 Leads + Tab), TO-252AD |
| Surface Mount | YES |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Published | 2009 |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Subcategory | Peripheral Drivers |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 28V |
| Reach Compliance Code | compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | AUIPS7145R |
| JESD-30 Code | R-PSSO-G5 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Supply Voltage-Max (Vsup) | 60V |
| Power Supplies | 28V |
| Supply Voltage-Min (Vsup) | 6V |
| Interface | On/Off |
| Current - Output (Max) | 2.1A |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 6V~60V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Fixed), Over Temperature |
| Turn On Time | 20 μs |
| Rds On (Typ) | 75m Ω |
| Turn Off Time | 80 μs |
| Built-in Protections | TRANSIENT; OVER CURRENT; THERMAL |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 2.39mm |
| Length | 6.54mm |
| Width | 6.095mm |
| RoHS Status | RoHS Compliant |
AUIPS7145R Overview
It is package in Tube case.Package TO-252-5, DPak (4 Leads + Tab), TO-252AD contains it.In this case, the LED driving board is mounted as Surface Mount.General Purpose is the switch type it owns.It is recommended to set the temperature to -40°C~150°C TJ in order to ensure reliable operation.The LED driver is equipped with 1 outputs.A voltage of Not Required is used to power it.A maximum output voltage of N-Channel volts can be achieved by this LED driver.It comes under the family of AUIPS7145R.The termination count is 5.As far as functions are concerned, the lighting driver has 1.In this case, the LED driving board can produce only 2.1AV as its maximum output.It is possible to achieve a high level of efficiency with a supply voltage of 28V.There is an electrical component included in the Automotive, AEC-Q100 series.It is self-contained in an econtainer with a capacity of Peripheral Drivers.The Vsup value (maximum supply voltage) is set to 60V.In order to operate normally, the supply voltage (Vsup) must be maintained above 6V.This part is powered by 28V.
AUIPS7145R Features
Supplied from 28V
AUIPS7145R Applications
There are a lot of Infineon Technologies AUIPS7145R Power Switches ICs applications.
- Wireless Headsets
- PC Cards
- Wireless Modem Data Cards
- Hot Swap
- Portable GPS Device
- Smartphone and PDA
- Various applications equipped with buttons
- Solid-State Drives
- USB Power Distribution
- Low Voltage I/O System Power
