BA2904YFVM-CTR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 8-VSSOP, 8-MSOP (0.110, 2.80mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| Published | 2013 |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e2 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Copper (Sn/Cu) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Circuits | 2 |
| Current - Supply | 500μA |
| Slew Rate | 0.2V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 20nA |
| Voltage - Supply, Single/Dual (±) | 3V~36V ±1.5V~18V |
| Bandwidth | 500 kHz |
| Unity Gain BW-Nom | 500 kHz |
| Average Bias Current-Max (IIB) | 0.1μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 36V |
| Voltage - Input Offset | 2mV |
| Current - Output / Channel | 30mA |
| Bias Current-Max (IIB) @25C | 0.06μA |
| Height Seated (Max) | 0.9mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
BA2904YFVM-CTR Overview
There is a 8-VSSOP, 8-MSOP (0.110, 2.80mm Width) case package that contains the instrumentation amplifiers. Op amps are General Purpose types of amplifier on the chip. There is a Cut Tape (CT) case that is delivered with the instrumentation amplifiers. The number of terminations approaches 8. Buffer amplifier has a total of 8 pins. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. A total of 8 pins are present on the instrumentation amplifier. For this electronic part, it is recommended that you mount it with type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . This op amp ic has 2 circuits. This linear amplifier pack is based on the TAPE AND REEL axis. We recommend that you use this electronic part with an 500μA supply in order to get the best performance from it. Automotive, AEC-Q100 corresponds to the op amp's series.
BA2904YFVM-CTR Features
8 Pins
supply voltage of 5V
BA2904YFVM-CTR Applications
There are a lot of ROHM Semiconductor BA2904YFVM-CTR Instrumentational OP Amps applications.
- Scintillation detectors
- Signal amplification
- Hand-held batteries
- Broadcasting
- Commercial audio systems
- Multimedia playback equipment
- RF cable systems
- Semiconductor detectors
- Medical instruments
- Precision measurement
