BD2202G-TR
| Parameters | |
|---|---|
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 150mOhm |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 675mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Base Part Number | BD220* |
| Pin Count | 5 |
| Number of Outputs | 1 |
| Output Voltage | 3.9V |
| Output Type | N-Channel |
| Max Output Current | 400mA |
| Power Supplies | 3/3.3V |
| Supply Voltage-Min (Vsup) | 2.7V |
| Interface | On/Off |
| Nominal Supply Current | 70μA |
| Output Configuration | High Side |
| Power Dissipation | 675mW |
| Output Current | 200mA |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Turn On Delay Time | 10 ms |
| Max Output Voltage | 6.3V |
| Switch Type | General Purpose |
| Max Input Voltage | 3.6V |
| Output Current per Channel | 200mA |
| Nominal Input Voltage | 3.6V |
| Turn-Off Delay Time | 200 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~3.6V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, UVLO |
| Output Peak Current Limit-Nom | 0.2A |
| Rds On (Typ) | 150m Ω |
| Built-in Protections | OVER CURRENT; THERMAL; UNDER VOLTAGE |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -25°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
BD2202G-TR Overview
It is package in Tape & Reel (TR) case.It is included in the package SC-74A, SOT-753.In this case, the LED driving board is mounted as Surface Mount.There is a General Purpose switch type associated with it.To ensure reliable operation, the temperature should be set to -25°C~85°C TA.As a default, the output is set to 1.Operation is based on a supply voltage of Not Required.The maximum output voltage of this LED driver is N-Channel volts.I believe it belongs to the BD220* family.It contains 5 terminations.For operation, we use the 5 pins.The LED driving board has a total of 1 functions.The maximum output current is reduced to 400mA to meet the operation criteria.It is possible to achieve a high level of efficiency with a supply voltage of 3.3V.The lighting driver is mounted in the direction of Surface Mount.In total, it has 5 pins.The LED driver has 150mOhm resistance.When this case is used, the output current is set to 200mA.Self-contained in an econtainer with a capacity of Peripheral Drivers, this LED driver is self-contained.In order to operate normally, the supply voltage (Vsup) must be maintained above 2.7V.This part is powered by 3/3.3V.This LED driving board can accept voltages up to 3.6V volts as an input.
BD2202G-TR Features
Supplied from 3.3V
Resistance of 150mOhm
BD2202G-TR Applications
There are a lot of ROHM Semiconductor BD2202G-TR Power Switches ICs applications.
- USB3.1 Power Delivery
- Hot Swaps
- Portable/Handheld Devices
- Set-Top Boxes
- Low Voltage I/O System Power
- Wireless Headsets
- Hot-Swap Systems
- HDD and SSD
- Storage Drives
- Portable Music Players
