BD4842FVE-TR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-665 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~105°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Series | BD48xxx |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Type | Voltage Detector |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 100mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | FLAT |
| Number of Functions | 1 |
| Supply Voltage | 4V |
| Base Part Number | BD48 |
| Output | Open Drain or Open Collector |
| Pin Count | 5 |
| Power Supplies | 4.2V |
| Number of Channels | 1 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 950mV |
| Nominal Supply Current | 900nA |
| Max Supply Current | 1.68μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 4.2V |
| Number of Voltages Monitored | 1 |
| Min Reset Threshold Voltage | 4.137V |
| Max Reset Threshold Voltage | 4.263V |
| Threshold Voltage | +4.2V |
| Height Seated (Max) | 0.6mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
BD4842FVE-TR Overview
As you can see, this power management is mounted through 5 terminals. Tape & Reel (TR)-packaging is used. Power management is possible to find a series of 1 functions. Power management consists of 1 channels, each of which can be used independently. In this IC management you will find SOT-665 functions for you to refer to. This IC power shares lots of benefits with other Voltage Detector products. When a supply voltage of 4V is applied to the power ic, it conducts. When 1 is applied to the power ic, it conducts. Surface Mount mounts IC management. This power ic can be sub-categorized as Power Management Circuits. It has a total of 5 pins that are attached to IC management. 5 pins are on the supervisor. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 950mV. The maximum supply voltage (Vsup) in this PMIC should not exceed 10V volts. The recommended mounting type is Surface Mount. The temperature of the supervisors should be set to this range: -40°C~105°C TA. The output voltage of this power managment ic during operation is Open Drain or Open Collector. It is always advisable to use BD48, the base supervisor number, when searching for similar PMICs from the manufacturer. The voltage supervisor requires a power source of 4.2V volts in order to work correctly. The power management can work with a maximum supply temperature of 1.68μA. It is one of the well-known BD48xxx series power ic line.
BD4842FVE-TR Features
Voltage Detector type
Minimum supply voltage of 950mV
BD4842FVE-TR Applications
There are a lot of ROHM Semiconductor BD4842FVE-TR Voltage Supervisors applications.
- Stable power system
- Medical-specific isolation transformer
- Insulation fault location system
- Detection of phase loss
- Power distribution systems of CCU
- Fire equipment power monitoring system
- Embedded computing
- Radio
- Magnetic resonance imaging
- DC stabilized power supply module
