BD6212FP-E2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 25-SOP (0.213, 5.40mm Width) + 2 Heat Tabs |
| Number of Pins | 25 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 25 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Applications | Media Player |
| Subcategory | Motion Control Electronics |
| Technology | Power MOSFET |
| Voltage - Supply | 3V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.8mm |
| Frequency | 100kHz |
| Base Part Number | BD621* |
| Function | Driver - Fully Integrated, Control and Power Stage |
| Output Voltage | 7V |
| Max Output Current | 2A |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Channels | 1 |
| Interface | On/Off |
| Analog IC - Other Type | BRUSH DC MOTOR CONTROLLER |
| Nominal Supply Current | 1.5mA |
| Output Configuration | Half Bridge (2) |
| Max Output Voltage | 7V |
| Voltage - Load | 3V~5.5V |
| Drain to Source Resistance | 500mOhm |
| Motor Type - AC, DC | Brushed DC |
| Width | 5.4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
BD6212FP-E2 Overview
The design contains a Tape & Reel (TR)package.There is 25-SOP (0.213, 5.40mm Width) + 2 Heat Tabs case included with the part.Surface Mountshould be used for mounting the part.Drivers controllers is fDrivers controllersting for the component connected in Media Player.The device is capable of supplying a voltage of 3V~5.5V volts.With regard to operating temperature, it ranges -40°C~150°C TJ. The motor type can be classified as Brushed DC.A total of 25terminations are available in the part.Drivers controllers is possible to apply voltage at a rate of 3V~5.5Vto the load.Drivers controllers is important to remember that this amplifier should be run at 5V.There is a recommended mounting method of Surface Mount.A BRUSH DC MOTOR CONTROLLERanalog IC is employed in this device.This can be determined by looking at the BD621* part number.25pins are available on the device.Drivers controllers belongs to Motion Control Electronics series.The output voltage is maintained at 7V.For optimal operation, its maximum output current reaches [0].There are 1 channels on it.Controller ic is possible to achieve the frequency of 100kHz.
BD6212FP-E2 Features
Applications : Media Player
Load voltage across the chip 3V~5.5V
base on BD621* number
BD6212FP-E2 Applications
There are a lot of ROHM Semiconductor BD6212FP-E2 motor drivers applications.
- Accurate LED current matching
- PDAs
- Handheld devices
- Architectural lighting
- Monitoring the energy that the luminaire uses
- CHMSL (center high-mount stop lamps)
- Tail lights
- High brightness LED lighting
- Outdoor area lights
- drivers for outdoor application
