BD6222FP-E2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 25-SOP (0.213, 5.40mm Width) + 2 Heat Tabs |
| Number of Pins | 25 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 25 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Applications | DC Motors, General Purpose |
| Subcategory | Motion Control Electronics |
| Technology | Power MOSFET |
| Voltage - Supply | 6V~15V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Terminal Pitch | 0.8mm |
| Base Part Number | BD622* |
| Pin Count | 25 |
| Number of Outputs | 1 |
| Supply Voltage-Min (Vsup) | 6V |
| Interface | Logic |
| Analog IC - Other Type | BRUSH DC MOTOR CONTROLLER |
| Nominal Supply Current | 2.5mA |
| Output Configuration | Half Bridge (2) |
| Output Current | 2A |
| Output Current per Channel | 2A |
| Voltage - Load | 6V~15V |
| Fault Protection | Current Limiting, Over Temperature, Over Voltage, UVLO |
| Rds On (Typ) | 1 Ω |
| Load Type | Inductive |
| Height | 1.9mm |
| Length | 13.6mm |
| Width | 5.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
BD6222FP-E2 Overview
For packaging, Tape & Reel (TR) is used.H bridge is included in the 25-SOP (0.213, 5.40mm Width) + 2 Heat Tabs package as a cost-saving measure.Bridge driver is possible to ensure improved reliabilbridge drivery by varying the supply voltage of 6V~15V.In the way of Surface Mount, H bridge circuit is mounted.When -40°C~85°C TA is operating at a certain temperature, motor driver H bridge can function normally.Among H bridge motor drivers many uses, H bridge motor driver can be found in DC Motors, General Purpose as well.Mount the board using Surface Mount.25 terminations are used to terminate transmission lines with H bridges that match their characteristic impedance.It is used as a pronged contact as H bridge ic of a signal interface when 25 pins are used.Its base H bridge ic number of BD622* is the basis to find more related H bridge ics.For the operation of the H bridge, a voltage supply of 12V is used.H bridge circuit contains an analog IC type BRUSH DC MOTOR CONTROLLER.A current of 2A flows through the pins of the output and power supply.A number of 25 pins work together to provide this bridge driver with its specific functions.It is equipped with 1 outputs.H bridge motor drivers in the Motion Control Electronics subcategory have a number of similarities.
BD6222FP-E2 Features
Available in 25-SOP (0.213, 5.40mm Width) + 2 Heat Tabs Package / Case
Operating Temperature at the range of Surface Mount
Interface IC Type : BD622*
BD6222FP-E2 Applications
There are a lot of ROHM Semiconductor BD6222FP-E2 Full Bridge Drivers, Half-Bridge Drivers applications.
- High current, low profile DC-DC converters
- Networking Microprocessor Voltage Regulators
- Industrial Pumps
- Compact Blade Servers
- Desktop Computers
- DC-DC Converters
- Industrial Fans
- High-Current DC-DC Point-of-Load Converters
- Voltage Regulators
- Voltage Regulators for CPUs
