BD6225FP-E2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 25-SOP (0.213, 5.40mm Width) + 2 Heat Tabs |
| Number of Pins | 25 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 25 |
| ECCN Code | EAR99 |
| Applications | DC Motors, General Purpose |
| Subcategory | Motion Control Electronics |
| Technology | Power MOSFET |
| Voltage - Supply | 6V~15V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Terminal Pitch | 0.8mm |
| Base Part Number | BD622* |
| Pin Count | 25 |
| Number of Outputs | 2 |
| Supply Voltage-Max (Vsup) | 15V |
| Supply Voltage-Min (Vsup) | 6V |
| Interface | Logic |
| Analog IC - Other Type | BRUSH DC MOTOR CONTROLLER |
| Nominal Supply Current | 1.3mA |
| Output Configuration | Half Bridge (4) |
| Output Current | 500mA |
| Output Current per Channel | 500mA |
| Supply Current-Max (Isup) | 3.5mA |
| Collector Emitter Voltage (VCEO) | 18V |
| Max Collector Current | 500mA |
| Voltage - Load | 6V~15V |
| Fault Protection | Current Limiting, Over Temperature, Over Voltage, UVLO |
| Rds On (Typ) | 1.5 Ω |
| Motor Type | Brushed |
| Load Type | Inductive |
| Height | 1.9mm |
| Length | 13.6mm |
| Width | 5.4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
BD6225FP-E2 Overview
Packaged using Tape & Reel (TR).As a cost-saving measure, H bridge is included in the 25-SOP (0.213, 5.40mm Width) + 2 Heat Tabs package.The supply voltage 6V~15V has the capabilbridge drivery of improving reliabilbridge drivery.H bridge circuit is mounted in the way of Surface Mount.-40°C~85°C TA can work normally at motor driver H bridges operating temperature.There are lots of uses for H bridge motor driver, including DC Motors, General Purpose.On the PCB H gate is mounted using Surface Mount.A transmission line can be terminated at a 25 termination with the H bridge whose characteristic impedance matches the transmission line.As H bridge ic of the signal interface, 25 pins are used as pronged contacts.In addition to the BD622* H bridge ic number, more related H bridge ics can be located by using its base H bridge ic number.This H bridge operates with a voltage of 12V.IC type BRUSH DC MOTOR CONTROLLER is used as H bridge circuit's analog IC.The output and power supply pins are flowing wH-bridgeh current 500mA.A number of 25 pins work together to provide this bridge driver with its specific functions.There is a 2 output on it.This H bridge motor driver falls under the subcategory of Motion Control Electronics.
BD6225FP-E2 Features
Available in 25-SOP (0.213, 5.40mm Width) + 2 Heat Tabs Package / Case
Operating Temperature at the range of Surface Mount
Interface IC Type : BD622*
BD6225FP-E2 Applications
There are a lot of ROHM Semiconductor BD6225FP-E2 Full Bridge Drivers, Half-Bridge Drivers applications.
- Compact Blade Servers
- Networking Microprocessor Voltage Regulators
- Home Appliances
- VTR
- Optical disc drives
- Voltage Regulators
- High current, low profile DC-DC converters
- Notebook Computers
- Industrial Pumps
- High-Performance Gaming Motherboards
