banner_page

BD6226FP-E2

BD6226FP-E2 datasheet pdf and PMIC - Full, Half-Bridge Drivers product details from ROHM Semiconductor stock available at Noco


  • Manufacturer: ROHM Semiconductor
  • Nocochips NO: 687-BD6226FP-E2
  • Package: 25-SOP (0.213, 5.40mm Width) + 2 Heat Tabs
  • Datasheet: -
  • Stock: 674
  • Description: BD6226FP-E2 datasheet pdf and PMIC - Full, Half-Bridge Drivers product details from ROHM Semiconductor stock available at Noco(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 25-SOP (0.213, 5.40mm Width) + 2 Heat Tabs
Number of Pins 25
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2012
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 25
Termination SMD/SMT
ECCN Code EAR99
Applications DC Motors, General Purpose
Subcategory Motion Control Electronics
Technology Power MOSFET
Voltage - Supply 6V~15V
Terminal Position DUAL
Terminal Form GULL WING
Number of Functions 1
Supply Voltage 12V
Terminal Pitch 0.8mm
Frequency 100kHz
Base Part Number BD622*
Pin Count 25
Output Voltage 18V
Supply Voltage-Max (Vsup) 15V
Supply Voltage-Min (Vsup) 6V
Number of Channels 2
Interface Logic
Analog IC - Other Type BRUSH DC MOTOR CONTROLLER
Nominal Supply Current 2mA
Output Configuration Half Bridge (4)
Output Current 1A
Max Output Voltage 18V
Output Current per Channel 1A
Supply Current-Max (Isup) 3.5mA
Voltage - Load 6V~15V
Fault Protection Current Limiting, Over Temperature, Over Voltage, UVLO
Rds On (Typ) 1.5 Ω
Drain to Source Resistance 1.5Ohm
Load Type Inductive
Length 13.6mm
Width 5.4mm
Radiation Hardening No
REACH SVHC Unknown
RoHS Status ROHS3 Compliant
Lead Free Lead Free

BD6226FP-E2 Overview


Tape & Reel (TR) is used for packaging.H bridge is included in the 25-SOP (0.213, 5.40mm Width) + 2 Heat Tabs package as a cost-saving measure.Bridge driver is possible to improve the reliabilbridge drivery of 6V~15V by increasing the supply voltage.There is a mounting of H bridge circuit in Surface Mount.Motor driver H bridge is possible for -40°C~85°C TA to operate normally at motor driver H bridges operating temperature.H bridge motor driver is pretty useful in a wide range of applications, including DC Motors, General Purpose.Surface Mount is adopted as a technique to mount H gate on the PCB.It is possible to terminate a transmission line with a 25 termination using the H bridge which matches the characteristic impedance of the transmission line.Signal interfaces include 25 pins that serve as pronged contacts.Its base H bridge ic number, BD622*, can be used to locate other H bridge ics that are related.This H bridge operates with a voltage of 12V.The analog IC type of this H bridge is BRUSH DC MOTOR CONTROLLER.As a result of the current flowing through the output and power supply pins, there is a current of 1A.A bridge driver's 25 pins work together in order to perform its specific functions.This H bridge motor driver belongs to the subcategory of Motion Control Electronics and shares several similarities with other parts in that category.In this case, the voltage released by the Hbridge is 18V.

BD6226FP-E2 Features


Available in 25-SOP (0.213, 5.40mm Width) + 2 Heat Tabs Package / Case
Operating Temperature at the range of Surface Mount
Interface IC Type : BD622*

BD6226FP-E2 Applications


There are a lot of ROHM Semiconductor BD6226FP-E2 Full Bridge Drivers, Half-Bridge Drivers applications.

  • Non-V-Core
  • CD players
  • High-Performance Gaming Motherboards
  • Home Appliances
  • Small Form-Factor Voltage Regulator Modules
  • Bipolar stepper motor
  • Compact Blade Servers
  • PC peripherals
  • Voltage Regulators
  • High current, low profile DC-DC converters

Write a review

Note: HTML is not translated!
    Bad           Good