BD6517F-E2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.173, 4.40mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -25°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| Feature | Status Flag |
| Pbfree Code | yes |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 110mOhm |
| Additional Feature | CONTROL LOGIC: ACTIVE LOW |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 560mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | BD651* |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Output Voltage | 6V |
| Output Type | N-Channel |
| Max Output Current | 500mA |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 3V |
| Interface | On/Off |
| Nominal Supply Current | 500mA |
| Output Configuration | High Side |
| Power Dissipation | 560mW |
| Output Current | 500mA |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Turn On Delay Time | 2 ms |
| Max Output Voltage | 6.3V |
| Switch Type | USB Switch |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Nominal Input Voltage | 5.5V |
| Turn-Off Delay Time | 20 μs |
| Min Output Voltage | -300mV |
| Ratio - Input:Output | 1:2 |
| Voltage - Load | 3V~5.5V |
| Driver Number of Bits | 2 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Reverse Current, UVLO |
| Turn On Time | 6000 µs |
| Output Peak Current Limit-Nom | 1.65A |
| Rds On (Typ) | 110m Ω |
| Built-in Protections | OVER CURRENT; OVER VOLTAGE; THERMAL |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
BD6517F-E2 Overview
The package is in the form of a Tape & Reel (TR).Package 8-SOIC (0.173, 4.40mm Width) contains it.A Surface Mount mounting is used for the LED driving board.A USB Switch switch type is owned by it.The temperature should be set to -25°C~85°C TA to ensure reliable functioning.There are 2 outputs available on this lighting driver.A voltage of Not Required is used to power it.It has a maximum output voltage of N-Channel volts.A lighting driver with Status Flag features is available.It belongs to the BD651* family.It has a total of 8 terminations.The 8 pins are used to operate the LED driver.It is important to note that the LED driving board has 2 functions.It is necessary to reduce the maximum output current to 500mA to meet the operation criteria.Supply voltages of 5V allow for high efficiency.It is mounted in the way of Surface Mount.8 pins are connected to it in total.110mOhm is the resistance of the lighting driver.In this case, the output current will be set to 500mA.This LED driver is self-contained in an econtainer with a capacity of Peripheral Drivers.To maintain a normal operation, the supply voltage (Vsup) must be maintained above 3V.The power supply of the part is 5V.It has a maximum input voltage of 5.5V volts.As far as input voltage goes, it has a minimum of 2.7V volts.As well as producing CONTROL LOGIC: ACTIVE LOW, this LED driving board is capable of producing [1].
BD6517F-E2 Features
Supplied from 5V
Resistance of 110mOhm
Additional features like CONTROL LOGIC: ACTIVE LOW
BD6517F-E2 Applications
There are a lot of ROHM Semiconductor BD6517F-E2 Power Switches ICs applications.
- Wireless Headsets
- Low Voltage I/O System Power
- Telecom and Network Systems
- USB Protection
- Set-top-box
- Wireless/Networking Cards
- USB3.1 Power Delivery
- Mobile Communication Devices
- Portable/Handheld Devices
- Hard Disk Drives
