BD6529GUL-E2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 6-SMD, Flat Lead Exposed Pad |
| Surface Mount | YES |
| Operating Temperature | -25°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Published | 2009 |
| Feature | Load Discharge, Slew Rate Controlled |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Subcategory | Power Management Circuits |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 6 |
| JESD-30 Code | R-PBGA-B6 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Max Output Current | 500mA |
| Power Supplies | 3.3V |
| Supply Voltage-Min (Vsup) | 2.7V |
| Number of Channels | 1 |
| Interface | On/Off |
| Analog IC - Other Type | POWER SUPPLY SUPPORT CIRCUIT |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Adjustable Threshold | NO |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Supply Current-Max (Isup) | 0.03mA |
| Nominal Input Voltage | 4.5V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~4.5V |
| Rds On (Typ) | 100m Ω |
| Height Seated (Max) | 0.55mm |
| RoHS Status | ROHS3 Compliant |
BD6529GUL-E2 Overview
It is package in Cut Tape (CT) case.There is a 6-SMD, Flat Lead Exposed Pad package that includes it.The lighting driver has the mounting type Surface Mount.The switch type is General Purpose.In order to guarantee reliable performance, the temperature should be set to -25°C~85°C TA.There are 1 outputs available on this lighting driver.In order to operate, it requires a voltage supply of Not Required.The maximum output voltage of this LED driver is N-Channel volts.As far as features are concerned, the LED driving board has Load Discharge, Slew Rate Controlled.The termination count is 6.It is important to note that the LED driving board has 1 functions.The maximum output current must drop to 500mA to meet the operation criteria.High efficiency is possible at 3.3V supply voltage.The LED driving board is equipped with a total of 6 pins.A self-contained LED driver with a capacity of Power Management Circuits is contained in an econtainer.Normal operation requires a voltage above 2.7V for the supply voltage.This LED driving board uses an analog IC POWER SUPPLY SUPPORT CIRCUIT.We currently have 1 channels available.This part is powered by 3.3V.In order to operate, it requires at most 0.03mA amps of supply current.
BD6529GUL-E2 Features
Supplied from 3.3V
1 channels
BD6529GUL-E2 Applications
There are a lot of ROHM Semiconductor BD6529GUL-E2 Power Switches ICs applications.
- Storage Drives
- Hot Swaps
- PC Cards
- Portable GPS
- Various applications equipped with buttons
- Wireless/Networking Cards
- Wearable Devices
- Hot-Swap Systems
- USB3.1 Power Delivery
- HDD, SSD
