BD6886GUL-E2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 15-UFBGA, CSPBGA |
| Number of Pins | 6 |
| Operating Temperature | -25°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| Pbfree Code | yes |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 15 |
| ECCN Code | EAR99 |
| Applications | DC Motors, General Purpose |
| Subcategory | Motion Control Electronics |
| Max Power Dissipation | 730mW |
| Technology | Power MOSFET |
| Voltage - Supply | 2.5V~5.5V |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | BD6886 |
| Pin Count | 15 |
| Number of Outputs | 1 |
| Operating Supply Voltage | 3V |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 35V |
| Supply Voltage-Min (Vsup) | 2.5V |
| Interface | Logic |
| Analog IC - Other Type | VOICE COIL MOTOR CONTROLLER |
| Output Configuration | Half Bridge (2) |
| Output Current | 200mA |
| Voltage - Load | 2.5V~5.5V |
| Current - Output / Channel | 150mA |
| Fault Protection | Over Temperature, UVLO |
| Rds On (Typ) | 800m Ω |
| Load Type | Inductive |
| Height Seated (Max) | 0.55mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
BD6886GUL-E2 Overview
It is packaged with Tape & Reel (TR).For cost-saving purposes, H bridge is included in the 15-UFBGA, CSPBGA package.The supply voltage 2.5V~5.5V has the capabilbridge drivery of improving reliabilbridge drivery.H bridge circuit is put into place according to the way of Surface Mount.The operating temperature of -25°C~150°C TJ enables motor driver H bridge to work normally.H bridge motor driver has many applications, including DC Motors, General Purpose.The PCB is mounted wH gateh Surface Mount.Transmission lines can be terminated with a termination that matches the characteristic impedance of the line using 15 terminations.An interface using 6 pins is used to provide pronged contact.Its base H bridge ic number, BD6886, can be used to locate other H bridge ics that are related.H bridge circuit operates on a voltage of 5V.H bridge circuit contains an analog IC type VOICE COIL MOTOR CONTROLLER.The power supply pins and the output pins are conducting a current of 200mA.It is the 15 pins that enable this bridge driver to perform its specific functions.It is equipped with 1 outputs.This H bridge motor driver falls under the subcategory of Motion Control Electronics. It is similar to other parts within that category.The operating supply voltage is maintained at 3V in order to ensure high efficiency.35V supplies electricity to the electrical load.
BD6886GUL-E2 Features
Available in 15-UFBGA, CSPBGA Package / Case
Operating Temperature at the range of Surface Mount
Interface IC Type : BD6886
Number of Receivers: 3V
BD6886GUL-E2 Applications
There are a lot of ROHM Semiconductor BD6886GUL-E2 Full Bridge Drivers, Half-Bridge Drivers applications.
- Quad DC motor
- Industrial Fans
- Networking Microprocessor Voltage Regulators
- DVD players
- DC-DC Converters
- V-Core
- High-Performance Gaming Motherboards
- Notebook Computers
- Small Form-Factor Voltage Regulator Modules
- High current, low profile DC-DC converters
