BD9763FVM-TR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Copper, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-VSSOP, 8-MSOP (0.110, 2.80mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Pbfree Code | yes |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Terminal Pitch | 0.65mm |
| Base Part Number | BD9763 |
| Function | Step-Up |
| Number of Outputs | 1 |
| Output Voltage | 2.5V |
| Output Type | Transistor Driver |
| Max Output Current | 125mA |
| Input Voltage-Nom | 7V |
| Analog IC - Other Type | SWITCHING REGULATOR |
| Output Configuration | Positive |
| Output Current | 850mA |
| Voltage - Supply (Vcc/Vdd) | 4V~9V |
| Control Features | Enable, Soft Start |
| Input Voltage (Min) | 4V |
| Topology | Boost |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 100kHz~1.2MHz |
| Input Voltage (Max) | 9V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Switcher Configuration | SINGLE |
| Max Frequency | 1.2MHz |
| Duty Cycle (Max) | 90% |
| Height Seated (Max) | 0.9mm |
| Length | 2.9mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
BD9763FVM-TR Overview
Capsuled in the 8-VSSOP, 8-MSOP (0.110, 2.80mm Width) package, the switching controller suits most application needs. It is sufficient to generate 1 outputs with this dc motor controller. A solid enclosure of Tape & Reel (TR) surrounds pmic. There are Transistor Driver dc switching's output (s) that it can handle. A 4V~9V voltage is supplied to the dc control and used for operating it. Suitable for work in a -40°C~85°C TA dc switcher. It can switch at 100kHz~1.2MHz. dc dc regulator is made easier with Surface Mount. Switching control is made easier with the dcdc regulator's Enable, Soft Start. An analog IC with the SWITCHING REGULATOR signal is connected to the switch converters. The switching converters's terminals (s) are designed at DUAL. A variety of dc switching's functions can be performed on 8 terminations. A few of the control techniques these dc dc converter ics adapt include PULSE WIDTH MODULATION. DC switcher's voltage input is 7V. Other relevant dc to dc converter ics can be found by searching "BD9763". There are only 8 pins on switching converter. There is a particular type of Switching Regulator or Controllers in switching converter. It is recommended that the input voltage of the dc dc voltage regulator be 4V. DC regulator outputs 2.5V voltage based on test statistics. It should be noted that the dc to dc regulator only accepts 9V voltage as input voltage. If you start a project, note down the dc dc regulator's usual output current of 850mA. DC switcher's Surface Mount qualifies it for most applications and prototypes. The max frequency of the pmic can reach 1.2MHz. There will be 125mA output current greater than 125mA from the dc switcher.
BD9763FVM-TR Features
Transistor Driver Outputs
Switching Frequency: 100kHz~1.2MHz
Enable, Soft Start
PULSE WIDTH MODULATION
BD9763FVM-TR Applications
There are a lot of ROHM Semiconductor BD9763FVM-TR DC to DC converter applications.
- Fire elevators
- Solar power plants
- Electrical power transmission
- Digital precision reference circuits
- Industrial controllers
- Product burn-in
- Medical equipment
- Planers
- Magnetohydrodynamic power
- Flaw detection equipment
