Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
TO-252-3, DPak (2 Leads + Tab), SC-63 |
Number of Pins |
3 |
Operating Temperature |
-40°C~150°C TJ |
Packaging |
Tape & Reel (TR) |
Published |
2007 |
Series |
HITFET® |
JESD-609 Code |
e3 |
Feature |
Auto Restart |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
2 |
ECCN Code |
EAR99 |
Terminal Finish |
Tin (Sn) |
Max Power Dissipation |
21W |
Technology |
MOS |
Terminal Position |
SINGLE |
Terminal Form |
GULL WING |
Number of Functions |
1 |
Supply Voltage |
12V |
Terminal Pitch |
2.28mm |
Base Part Number |
BTS118 |
Pin Count |
4 |
JESD-30 Code |
R-PSSO-G2 |
Number of Outputs |
1 |
Output Voltage |
42V |
Output Type |
N-Channel |
Interface |
On/Off |
Output Configuration |
Low Side |
Power Dissipation |
21W |
Output Current |
2.4A |
Voltage - Supply (Vcc/Vdd) |
Not Required |
Input Type |
Non-Inverting |
Switch Type |
General Purpose |
Halogen Free |
Halogen Free |
Drain to Source Voltage (Vdss) |
42V |
Nominal Input Voltage |
10V |
Ratio - Input:Output |
1:1 |
Voltage - Load |
42V Max |
Max Dual Supply Voltage |
42V |
Fault Protection |
Current Limiting (Fixed), Over Temperature, Over Voltage |
Output Peak Current Limit-Nom |
15A |
Rds On (Typ) |
70m Ω |
Built-in Protections |
TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
Height Seated (Max) |
2.5mm |
Length |
6.5mm |
Width |
6.22mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
BTS118DATMA1 Overview
As a result, it is packaged in the form of a Tape & Reel (TR).It is included with the TO-252-3, DPak (2 Leads + Tab), SC-63 package as well.The mounting type of the LED driver is Surface Mount.It owns the General Purpose switch type.To ensure reliable performance, the temperature should be set to -40°C~150°C TJ.The LED driver has 1 outputs.A supply voltage of Not Required is required for it to operate.The maximum output voltage is N-Channel volts.It has a total of Auto Restart features.It is part of the BTS118 family of LED drivers.There are 2 terminations in it.The 3 pins are used to operate the LED driver.The LED driving board has a total of 1 functions.The supply voltage can be 12V for high efficiency.The LED driving board is mounted in the way of Surface Mount.A total of 4 pins are present on it.This electrical component is part of the HITFET? series.This case has the output current set to 2.4A.
BTS118DATMA1 Features
Supplied from 12V
BTS118DATMA1 Applications
There are a lot of Infineon Technologies BTS118DATMA1 Power Switches ICs applications.
- Solid-State Drives
- Hot-Swap Systems
- HDD, SSD
- Storage Drives
- Various applications equipped with buttons
- Wireless Modem Data Cards
- Wearable Devices
- Portable GPS
- Notebook and Tablet Computers
- Hot Swap