BTS3018TCATMA1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-3, D2Pak (2 Leads + Tab), TO-263AB |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2014 |
| Series | HITFET® |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 2 |
| Additional Feature | SEATED HGT-NOM; SEATED HGT-CALCULATED |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| JESD-30 Code | R-PSSO-G2 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 6A |
| Supply Voltage-Min (Vsup) | 2V |
| Interface | On/Off |
| Nominal Supply Current | 1.4mA |
| Output Configuration | Low Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Halogen Free | Halogen Free |
| Drain to Source Voltage (Vdss) | 60V |
| Nominal Input Voltage | 10V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 60V Max |
| Max Dual Supply Voltage | 60V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Output Peak Current Limit-Nom | 6A |
| Rds On (Typ) | 18m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 4.5mm |
| Width | 9.25mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
BTS3018TCATMA1 Overview
It is packaged in the form of a Tape & Reel (TR).It is included with the TO-263-3, D2Pak (2 Leads + Tab), TO-263AB package as well.Mounting type Surface Mount is selected for the LED driving board.General Purpose is the type of switch owned by it.It is recommended to set the temperature to -40°C~150°C TJ in order to ensure reliable operation.In this LED driver, there are no outputs available.A supply voltage of Not Required is required for it to operate.A maximum output voltage of N-Channel volts can be achieved by this LED driver.It contains 2 terminations.Currently, the lighting driver has a total of 1 functions.To meet the operation criteria, the maximum output current drops to 6A.High efficiency is possible at 5V supply voltage.Surface Mount is mounted in the way of this LED driving board.This electrical component can be found in the HITFET? series.For normal operation, the supply voltage (Vsup) must be kept above 2V.Using this LED driver, it is also possible to produce SEATED HGT-NOM; SEATED HGT-CALCULATED.
BTS3018TCATMA1 Features
Supplied from 5V
Additional features like SEATED HGT-NOM; SEATED HGT-CALCULATED
BTS3018TCATMA1 Applications
There are a lot of Infineon Technologies BTS3018TCATMA1 Power Switches ICs applications.
- Portable Video Game Players
- HDD and SSD
- Storage (HDDs, SSDs)
- USB Power Distribution
- Hot Swap
- PC Cards
- Portable/Handheld Devices
- Mobile Communication Devices
- Portable GPS
- Hot-Swap Systems
