BTS3046SDLATMA1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-252-3, DPak (2 Leads + Tab), SC-63 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Series | HITFET® |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 2 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 13.5V |
| Terminal Pitch | 2.28mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | BTS3046 |
| Pin Count | 4 |
| JESD-30 Code | R-PSSO-G2 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Max Output Current | 3.6A |
| Supply Voltage-Min (Vsup) | 8V |
| Interface | On/Off |
| Nominal Supply Current | 10μA |
| Output Configuration | Low Side |
| Output Current | 3.6A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Halogen Free | Halogen Free |
| Drain to Source Voltage (Vdss) | 60V |
| Nominal Input Voltage | 10V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 60V Max |
| Max Dual Supply Voltage | 60V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Output Peak Current Limit-Nom | 4.3A |
| Rds On (Typ) | 46m Ω |
| Turn Off Time | 200 μs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Height Seated (Max) | 2.5mm |
| Length | 6.5mm |
| Width | 6.22mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
BTS3046SDLATMA1 Overview
It's?packaged?in?the way?of?a?Tape & Reel (TR).It is included in the package TO-252-3, DPak (2 Leads + Tab), SC-63.Mounting type Surface Mount is selected for the LED driving board.It owns General Purpose switch type.The temperature should be set to -40°C~150°C TJ to ensure reliable functioning.It is possible to use 1 outputs in the lighting driver.The LED driving board is powered by a voltage of Not Required.The maximum output voltage of this LED driver is N-Channel volts.It comes under the family of BTS3046.It has a total of 2 terminations.There are 1 functions of the LED driver.This operation requires the maximum output current to be decreased to 3.6A.The supply voltage can be 13.5V for high efficiency.It is positioned in the direction of Surface Mount.The LED driver has a total of 4 pins.It belongs to the HITFET? series.When this case is used, the output current is set to 3.6A.In order to operate normally, the supply voltage (Vsup) must be maintained above 8V.
BTS3046SDLATMA1 Features
Supplied from 13.5V
BTS3046SDLATMA1 Applications
There are a lot of Infineon Technologies BTS3046SDLATMA1 Power Switches ICs applications.
- Smartphone and PDA
- Wireless/Networking Cards
- Smart Phones, Feature Phones
- Hot Swap
- Portable Video Game Players
- Storage (HDDs, SSDs)
- Portable Devices
- Mobile Communication Devices
- Solid-State Drives
- USB Power Distribution
