BTS3080TFATMA1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | TO-252-3, DPak (2 Leads + Tab), SC-63 |
| Surface Mount | YES |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2017 |
| Series | HITFET® |
| JESD-609 Code | e3 |
| Feature | Auto Restart |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 2 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.28mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| JESD-30 Code | R-PSSO-G2 |
| Number of Outputs | 1 |
| Output Voltage | 40V |
| Output Type | N-Channel |
| Supply Voltage-Min (Vsup) | 3V |
| Interface | On/Off |
| Current - Output (Max) | 3A |
| Output Configuration | Low Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Nominal Input Voltage | 5.5V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 40V Max |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Output Peak Current Limit-Nom | 3A |
| Rds On (Typ) | 69m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 2.5mm |
| Length | 6.5mm |
| Width | 6.22mm |
| RoHS Status | ROHS3 Compliant |
BTS3080TFATMA1 Overview
It is packaged in the manner of a Tape & Reel (TR).There is a TO-252-3, DPak (2 Leads + Tab), SC-63 package that includes it.The LED driver is mounted as Surface Mount.There is a switch type of General Purpose.To ensure reliable operation, set the temperature to -40°C~150°C TJ.The LED driver has 1 outputs.The LED driving board operates at Not Required volts.It produces a maximum output voltage of N-Channel volts at its maximum output.As far as features are concerned, the LED driving board has Auto Restart.As a result, there are 2 terminations.As far as the lighting driver is concerned, there are 1 functions.3AV is the maximum output of the LED driver.High efficiency is possible when the supply voltage is set to 5V.A component of this type is included in the HITFET? series.To maintain a normal operation, the supply voltage (Vsup) must be maintained above 3V.
BTS3080TFATMA1 Features
Supplied from 5V
BTS3080TFATMA1 Applications
There are a lot of Infineon Technologies BTS3080TFATMA1 Power Switches ICs applications.
- Portable GPS Device
- Wireless Headsets
- Hot-Swap Systems
- Hard Disk Drives
- Portable/Handheld Devices
- PC Cards
- PC Card Hot Swap
- HDD, SSD
- Hot Swap
- Notebook PC
