BTS3104SDLATMA1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-252-3, DPak (2 Leads + Tab), SC-63 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Series | HITFET® |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 2 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Max Power Dissipation | 1W |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 13.5V |
| Terminal Pitch | 2.28mm |
| Base Part Number | BTS3104 |
| Pin Count | 4 |
| JESD-30 Code | R-PSSO-G2 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 2A |
| Supply Voltage-Min (Vsup) | 8V |
| Interface | On/Off |
| Nominal Supply Current | 10μA |
| Output Configuration | Low Side |
| Power Dissipation | 1W |
| Output Current | 2A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Halogen Free | Halogen Free |
| Drain to Source Voltage (Vdss) | 60V |
| Nominal Input Voltage | 10V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 60V Max |
| Max Dual Supply Voltage | 60V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Output Peak Current Limit-Nom | 2.5A |
| Rds On (Typ) | 104m Ω |
| Turn Off Time | 200 μs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Height Seated (Max) | 2.5mm |
| Length | 6.5mm |
| Width | 6.22mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
BTS3104SDLATMA1 Overview
It is packaged in the form of a Tape & Reel (TR).It is included in the package TO-252-3, DPak (2 Leads + Tab), SC-63.It has been mounted as Surface Mount on the LED driver.It owns General Purpose switch type.To ensure reliable operation, the temperature should be set to -40°C~150°C TJ.It is possible to use 1 outputs in the lighting driver.Operation is based on Not Required supply voltage.There is a maximum output voltage of N-Channel volts.The BTS3104 family contains this object.As a result, there are 2 terminations.It is important to note that the LED driving board has 1 functions.Maximum output current falls to 2A when operation criteria are met.Using a voltage of 13.5V allows for high efficiency.The LED driving board is mounted in the way of Surface Mount.A total of 4 pins are included in this LED driver.This electrical component is included in the HITFET? series.When this case is used, the output current is set to 2A.In order for the lighting driver to operate normally, the supply voltage (Vsup) should be maintained above 8V.
BTS3104SDLATMA1 Features
Supplied from 13.5V
BTS3104SDLATMA1 Applications
There are a lot of Infineon Technologies BTS3104SDLATMA1 Power Switches ICs applications.
- PC Card Hot Swap
- Notebook PC
- Storage Drives
- Hot Swap
- Hard Disk Drives
- Various applications equipped with buttons
- Portable Music Players
- Wearable Devices
- Low Voltage I/O System Power
- Solid State Drivers
