Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
TO-263-5, D2Pak (4 Leads + Tab), TO-263BB |
Number of Pins |
5 |
Operating Temperature |
-40°C~150°C TJ |
Packaging |
Tape & Reel (TR) |
Published |
2013 |
Series |
PROFET® |
JESD-609 Code |
e3 |
Feature |
Auto Restart |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
4 |
ECCN Code |
EAR99 |
Resistance |
50mOhm |
Terminal Finish |
Tin (Sn) |
Additional Feature |
SEATED HGT-NOM |
Max Power Dissipation |
75W |
Technology |
MOS |
Terminal Position |
SINGLE |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
1 |
Supply Voltage |
12V |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
JESD-30 Code |
R-PSSO-G4 |
Number of Outputs |
1 |
Output Type |
N-Channel |
Max Output Current |
5.8A |
Operating Supply Voltage |
34V |
Interface |
On/Off |
Nominal Supply Current |
1.8mA |
Output Configuration |
High Side |
Output Current |
7A |
Voltage - Supply (Vcc/Vdd) |
Not Required |
Max Supply Current |
3.5mA |
Propagation Delay |
1 ms |
Input Type |
Non-Inverting |
Turn On Delay Time |
400 μs |
Switch Type |
General Purpose |
Halogen Free |
Not Halogen Free |
Output Current per Channel |
7A |
Turn-Off Delay Time |
450 μs |
Ratio - Input:Output |
1:1 |
Voltage - Load |
5V~34V |
Fault Protection |
Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage, UVLO |
Output Peak Current Limit-Nom |
7A |
Rds On (Typ) |
50m Ω |
Built-in Protections |
TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
BTS426L1E3062ABUMA1 Overview
The LED driver's packaged as a Tape & Reel (TR).It's included in the TO-263-5, D2Pak (4 Leads + Tab), TO-263BB package.It has been mounted as Surface Mount on the LED driver.General Purpose is the switch type it owns.It is recommended that the temperature be set to -40°C~150°C TJ for reliable performance.By default, it is set to output 1.Operation is based on a supply voltage of Not Required.A maximum voltage of N-Channel volts is available from the output of this LED driver.It is equipped with Auto Restart features.It has a total of 4 terminations.For operation, we use the 5 pins.Currently, the lighting driver has a total of 1 functions.The maximum output current drops to 5.8A in order to meet the operation criteria.It is possible to obtain high efficiency with a supply voltage of 12V.This lighting driver is mounted in the way of Surface Mount.50mOhm is the resistance of the lighting driver.This electrical component can be found in the PROFET? series.This case results in a 7A output current.Optimal efficiency requires a voltage of 34V.This system has a maximum current requirement of 3.5mA.In addition, SEATED HGT-NOM can be produced using this LED driving board.
BTS426L1E3062ABUMA1 Features
Supplied from 12V
Resistance of 50mOhm
Additional features like SEATED HGT-NOM
BTS426L1E3062ABUMA1 Applications
There are a lot of Infineon Technologies BTS426L1E3062ABUMA1 Power Switches ICs applications.
- Hot Swaps
- Low Voltage I/O System Power
- Wireless/Networking Cards
- Storage (HDDs, SSDs)
- Notebook PC
- Hard Disk Drives
- Storage Drives
- Mobile Communication Devices
- HDD and SSD
- Hot-Swap Systems