BTS500402SFAXUMA1
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 36-BSSOP (0.295, 7.50mm Width) |
| Number of Pins | 36 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| Series | PROFET® |
| Feature | Slew Rate Controlled |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 36 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Pin Count | 36 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Max Output Current | 11A |
| Supply Voltage-Max (Vsup) | 5.5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Interface | Parallel |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | 4.5V~5.5V |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 6V~28V |
| Fault Protection | Over Temperature, Over Voltage, Short Circuit |
| Screening Level | AEC-Q100 |
| Turn On Time | 640 μs |
| Output Peak Current Limit-Nom | 11A |
| Rds On (Typ) | 4m Ω |
| Supply Voltage1-Nom | 13.5V |
| Turn Off Time | 340 μs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Supply Voltage1-Min | 6V |
| Width | 7.6mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
BTS500402SFAXUMA1 Overview
Tape & Reel (TR) is the way it's packaged.The 36-BSSOP (0.295, 7.50mm Width) package contains it.This LED driving board is mounted using the mounting type Surface Mount.General Purpose is the switch type that it owns.Ensure reliable operation by setting the temperature to -40°C~150°C TJ.The lighting driver is equipped with 2 outputs that can be used.A supply voltage of 4.5V~5.5V is required for it to operate.The maximum output voltage is N-Channel volts.As far as features are concerned, the LED driving board has Slew Rate Controlled.As a result, there are 36 terminations.It is necessary to use the 36 pins in order to operate the LED driver.It contains 1 functions.Maximum output current falls to 11A when operation criteria are met.With a supply voltage of 5V, high efficiency is possible.The LED driving board is mounted in the way of Surface Mount.The LED driving board is equipped with a total of 36 pins.A component of this type is included in the PROFET? series.The LED driver is configured with a maximum supply voltage of 5.5V (Vsup).Normal operation requires a voltage above 4.5V for the supply voltage.
BTS500402SFAXUMA1 Features
Supplied from 5V
BTS500402SFAXUMA1 Applications
There are a lot of Infineon Technologies BTS500402SFAXUMA1 Power Switches ICs applications.
- Solid-State Drives
- Storage (HDDs, SSDs)
- Hot Swap
- Low Voltage I/O System Power
- USB Ports/Hubs
- Portable Music Players
- PC Card Hot Swap
- Handheld Devices
- Portable GPS
- USB Protection
