BTS500801TMAATMA1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-8, D2Pak (7 Leads + Tab), TO-263CA |
| Surface Mount | YES |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | PROFET® |
| JESD-609 Code | e3 |
| Feature | Auto Restart |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 7 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Additional Feature | SEATED HGT-CALCULATED; SEATED HGT-NOM |
| Technology | MOS |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | BTS50080 |
| JESD-30 Code | R-PSSO-G7 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Supply Voltage-Max (Vsup) | 38V |
| Supply Voltage-Min (Vsup) | 5.5V |
| Interface | On/Off |
| Current - Output (Max) | 9.5A |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 5.5V~38V |
| Fault Protection | Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage |
| Turn On Time | 550 µs |
| Output Peak Current Limit-Nom | 12A |
| Rds On (Typ) | 7m Ω |
| Turn Off Time | 600 µs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 4.5mm |
| Width | 9.25mm |
| RoHS Status | ROHS3 Compliant |
BTS500801TMAATMA1 Overview
It is packaged in the manner of a Tape & Reel (TR).Package TO-263-8, D2Pak (7 Leads + Tab), TO-263CA contains it.It has been mounted as Surface Mount on the LED driver.This switch is of type General Purpose.The temperature should be set to -40°C~150°C TJ to ensure reliable functioning.The LED driver has 1 outputs.Operation is based on Not Required supply voltage.It has a maximum output voltage of N-Channel volts.Auto Restart features are available on the lighting driver.It is a member of the BTS50080 family.It has a total of 7 terminations.It contains 1 functions.There is a maximum output of 9.5AV from the LED driver.As long as the supply voltage is 12V, high efficiency can be achieved.This electrical component can be found in the PROFET? series.This LED driver is configured to have a maximum supply voltage of 38V (Vsup).A normal operation requires that the supply voltage (Vsup) remain above 5.5V.By using this lighting driver, it is also possible to produce SEATED HGT-CALCULATED; SEATED HGT-NOM.
BTS500801TMAATMA1 Features
Supplied from 12V
Additional features like SEATED HGT-CALCULATED; SEATED HGT-NOM
BTS500801TMAATMA1 Applications
There are a lot of Infineon Technologies BTS500801TMAATMA1 Power Switches ICs applications.
- Various applications equipped with buttons
- Hot Swap
- Hard Disk Drives
- Hot Swaps
- USB Protection
- PC Card Hot Swap
- PC Cards
- Gaming
- USB Power Distribution
- Portable GPS Device
