Parameters |
Mounting Type |
Surface Mount |
Package / Case |
TO-263-8, D2Pak (7 Leads + Tab), TO-263CA |
Surface Mount |
YES |
Number of Pins |
7 |
Operating Temperature |
-40°C~150°C TJ |
Packaging |
Tape & Reel (TR) |
Published |
2008 |
Series |
PROFET® |
Feature |
Auto Restart |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
7 |
ECCN Code |
EAR99 |
Resistance |
10mOhm |
Subcategory |
Peripheral Drivers |
Technology |
MOS |
Terminal Position |
SINGLE |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
1 |
Supply Voltage |
12V |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
BTS50090 |
Pin Count |
3 |
Number of Outputs |
1 |
Qualification Status |
Not Qualified |
Output Type |
N-Channel |
Max Output Current |
9A |
Supply Voltage-Max (Vsup) |
38V |
Supply Voltage-Min (Vsup) |
5.5V |
Interface |
On/Off |
Operating Supply Current |
1.4mA |
Output Configuration |
High Side |
Voltage - Supply (Vcc/Vdd) |
Not Required |
Input Type |
Non-Inverting |
Switch Type |
General Purpose |
Halogen Free |
Not Halogen Free |
Ratio - Input:Output |
1:1 |
Voltage - Load |
5.5V~38V |
Driver Number of Bits |
1 |
Fault Protection |
Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage |
Turn On Time |
600 μs |
Output Peak Current Limit-Nom |
11A |
Rds On (Typ) |
8m Ω |
Turn Off Time |
600 μs |
Built-in Protections |
TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
Output Current Flow Direction |
SINK |
Height Seated (Max) |
4.5mm |
Width |
9.25mm |
RoHS Status |
RoHS Compliant |
BTS50090-1TMA Overview
A Tape & Reel (TR) is used to package it.It is included with the TO-263-8, D2Pak (7 Leads + Tab), TO-263CA package as well.The lighting driver has the mounting type Surface Mount.The switch type is General Purpose.It is best to set the temperature to -40°C~150°C TJ to ensure reliable operation.The LED driver has 1 outputs.A voltage of Not Required is used to power it.It has a maximum output voltage of N-Channel volts.There are Auto Restart features available on the LED driving board.The BTS50090 family consists of this type.A total of 7 terminations have been found in it.The operation is carried out using the 7 pins.As far as functions are concerned, the lighting driver has 1.The maximum output current drops to 9A in order to meet the operation criteria.High efficiency is possible at 12V supply voltage.3 pins are equipped with it.The LED driver has 10mOhm resistance.There is an electrical component included in the PROFET? series.Self-contained LED driver with Peripheral Drivers capacity in an econtainer.This LED driver is configured to have a maximum supply voltage of 38V (Vsup).In order to operate normally, the supply voltage (Vsup) must be maintained above 5.5V.
BTS50090-1TMA Features
Supplied from 12V
Resistance of 10mOhm
BTS50090-1TMA Applications
There are a lot of Infineon Technologies BTS50090-1TMA Power Switches ICs applications.
- Solid State Drivers
- PC Card Hot Swap
- Telecom and Network Systems
- Hard Disk Drives
- Low Voltage I/O System Power
- USB Power Distribution
- Wireless Headsets
- Hot-Swap Systems
- Wearable Devices
- Wireless/Networking Cards