BTS621L1E3128ABUMA1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-8, D2Pak (7 Leads + Tab), TO-263CA |
| Number of Pins | 7 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| Series | PROFET® |
| JESD-609 Code | e3 |
| Feature | Auto Restart, Status Flag |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Max Power Dissipation | 75W |
| Technology | MOS |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| JESD-30 Code | R-PSSO-G6 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Max Output Current | 4.4A |
| Supply Voltage-Max (Vsup) | 34V |
| Supply Voltage-Min (Vsup) | 5V |
| Interface | On/Off |
| Nominal Supply Current | 4mA |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Switch Type | General Purpose |
| Halogen Free | Not Halogen Free |
| Nominal Input Voltage | 43V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 5V~34V |
| Fault Protection | Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage, UVLO |
| Screening Level | AEC-Q100 |
| Turn On Time | 400 μs |
| Output Peak Current Limit-Nom | 4.4A |
| Rds On (Typ) | 80m Ω |
| Turn Off Time | 400 μs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 4.5mm |
| Length | 10mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
BTS621L1E3128ABUMA1 Overview
As you can see, it's packaged in the way of a Tape & Reel (TR).There is a package for it in the TO-263-8, D2Pak (7 Leads + Tab), TO-263CA package.A Surface Mount mounting is used for the LED driving board.General Purpose is the type of switch owned by it.It is recommended that the temperature be set to -40°C~150°C TJ for reliable performance.There are 2 outputs available on this lighting driver.Operation is based on Not Required supply voltage.It has a maximum output voltage of N-Channel volts.Auto Restart, Status Flag features are available on the lighting driver.The termination count is 6.7 pins are used for operation.It is important to note that the LED driving board has 1 functions.The maximum output current is reduced to 4.4A to meet the operation criteria.With a supply voltage of 12V, high efficiency is possible.The lighting driver is mounted in the direction of Surface Mount.It is included in the PROFET? series.The maximum supply voltage for this LED driver is 34V (Vsup).In order for the lighting driver to operate normally, the supply voltage (Vsup) should be maintained above 5V.
BTS621L1E3128ABUMA1 Features
Supplied from 12V
BTS621L1E3128ABUMA1 Applications
There are a lot of Infineon Technologies BTS621L1E3128ABUMA1 Power Switches ICs applications.
- USB3.1 Power Delivery
- Portable GPS Device
- Hard Disk Drives
- Portable Video Game Players
- Hot-Swap Systems
- Set-top-box
- USB Power Distribution
- Storage (HDDs, SSDs)
- Solid-State Drives
- Hot Swap
