BTS707
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
| Series | PROFET® |
| Feature | Auto Restart, Status Flag |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 225mOhm |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 3W |
| Technology | MOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Supply Voltage | 12V |
| Base Part Number | BTS707 |
| Pin Count | 20 |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Max Output Current | 10A |
| Supply Voltage-Max (Vsup) | 58V |
| Supply Voltage-Min (Vsup) | 5.8V |
| Interface | On/Off |
| Current - Output (Max) | 1.6A |
| Nominal Supply Current | 2.2mA |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Output Current per Channel | 1.9A |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 5.8V~58V |
| Driver Number of Bits | 2 |
| Fault Protection | Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage |
| Turn On Time | 80 μs |
| Output Peak Current Limit-Nom | 2.8A |
| Rds On (Typ) | 225m Ω |
| Turn Off Time | 70 μs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Width | 7.6mm |
| RoHS Status | Non-RoHS Compliant |
BTS707 Overview
Tape & Reel (TR) is the way it's packaged.In the 20-SOIC (0.295, 7.50mm Width) package, it is included.A Surface Mount mounting is used for the LED driving board.General Purpose is the switch type that it owns.It is recommended to set the temperature to -40°C~150°C TJ in order to ensure reliable operation.It is possible to use 2 outputs in the lighting driver.A voltage of Not Required is used to power it.A maximum voltage of N-Channel volts is available from the output of this LED driver.There are Auto Restart, Status Flag features available on the LED driving board.It is a member of the BTS707 family.A total of 20 terminations have been recorded.The 20 pins are used for the operation of the system.The LED driving board has a total of 2 functions.This LED driver has a maximum output of 1.6AV.In order to meet the operation criteria, the maximum output current drops to 10A.The supply voltage can be 12V for high efficiency.Surface Mount is mounted in the way.It is equipped with a total of 20 pins.It has 225mOhm resistance.It is part of the PROFET? series.Self-contained LED driver with Peripheral Drivers capacity in an econtainer.A maximum supply voltage of 58V is set in Vsup.In order for this lighting driver to operate normally, the supply voltage (Vsup) should remain above 5.8V.
BTS707 Features
Supplied from 12V
Resistance of 225mOhm
BTS707 Applications
There are a lot of Infineon Technologies BTS707 Power Switches ICs applications.
- USB Power Distribution
- Portable/Handheld Devices
- Solid-State Drives
- USB Ports/Hubs
- Hot Swaps
- USB Protection
- Hard Disk Drives
- Set-Top Boxes
- HDD, SSD
- Hot Swap
