Parameters |
Supply Voltage |
12V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
BTS721L1 |
Pin Count |
20 |
JESD-30 Code |
R-PDSO-G20 |
Number of Outputs |
4 |
Qualification Status |
Not Qualified |
Output Type |
N-Channel |
Supply Voltage-Min (Vsup) |
5V |
Interface |
On/Off |
Current - Output (Max) |
2.5A |
Output Configuration |
High Side |
Voltage - Supply (Vcc/Vdd) |
Not Required |
Input Type |
Non-Inverting |
Switch Type |
General Purpose |
Ratio - Input:Output |
1:1 |
Voltage - Load |
5V~34V |
Fault Protection |
Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage |
Output Peak Current Limit-Nom |
9.8A |
Rds On (Typ) |
85m Ω |
Built-in Protections |
TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
Output Current Flow Direction |
SINK |
Height Seated (Max) |
2.65mm |
Length |
12.8mm |
Width |
7.6mm |
RoHS Status |
ROHS3 Compliant |
Factory Lead Time |
1 Week |
Mounting Type |
Surface Mount |
Package / Case |
20-SOIC (0.295, 7.50mm Width) |
Surface Mount |
YES |
Operating Temperature |
-40°C~150°C TJ |
Packaging |
Tape & Reel (TR) |
Published |
2010 |
Series |
PROFET® |
JESD-609 Code |
e3 |
Feature |
Auto Restart, Status Flag |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
3 (168 Hours) |
Number of Terminations |
20 |
ECCN Code |
EAR99 |
Terminal Finish |
Tin (Sn) |
Technology |
MOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
4 |
BTS721L1XUMA1 Overview
It is package in Tape & Reel (TR) case.There is a package for it in the 20-SOIC (0.295, 7.50mm Width) package.In this case, the LED driving board is mounted as Surface Mount.The switch type is General Purpose.It is recommended that the temperature be set to -40°C~150°C TJ for reliable operation.It is possible to use 4 outputs in the lighting driver.To operate, it needs a supply voltage of Not Required.Voltage output is N-Channel volts at maximum.As far as features are concerned, the LED driving board has Auto Restart, Status Flag.It is part of the BTS721L1 family of LED drivers.It has a total of 20 terminations.It consists of 4 functions.In this case, the LED driving board can produce only 2.5AV as its maximum output.With a supply voltage of 12V, high efficiency is possible.This LED driver is equipped with a total of 20 pins.This electrical component can be found in the PROFET? series.The supply voltage (Vsup) should be kept above 5V for normal operation.
BTS721L1XUMA1 Features
Supplied from 12V
BTS721L1XUMA1 Applications
There are a lot of Infineon Technologies BTS721L1XUMA1 Power Switches ICs applications.
- USB Power Distribution
- Portable GPS
- Hot-Swap Systems
- Hard Disk Drives
- Smart Phones, Feature Phones
- Solid State Drivers
- Hot Swap
- Mobile Communication Devices
- Wireless/Networking Cards
- Hot Swaps